Computer Science Exit Exam Study Guide · 184 questions
Read the question first. Select the eye beside the reading hint, study the cited module section, then reveal the answer. Each eye controls only its own block. All hints and answers start closed whenever this page opens.
Read the linked study-guide sections before revealing the answer. PDF page references count from the first page of the document.
184 of 184 questions
Question 1
Which one of the following is responsible for controlling the flow of bits between memory and controllers with no need for a constant intervention from the CPU?
A. Disk fragmenting
B. Memo, manager
C. Device controller
D. Direct memory access
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
DMA transfers a block directly between device and memory; the CPU supplies setup information and receives completion notification, rather than moving every word (PDF pp.107–108). This precisely meets the absence of constant intervention. A generic device controller alone does not establish DMA capability.
Evidence in the complete study note
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
Choice by choice
A · incorrect — Disk fragmenting is not the block-transfer mechanism described on pp.107–108.
B · incorrect — The corrupted name “Memo, manager” does not identify the DMA mechanism on p.107.
C · incorrect — An I/O controller can notify the CPU under interrupt I/O; that still leaves CPU data movement (p.106).
D · correct — Direct transfers and only beginning/end CPU involvement are explicit on p.108.
Question 2
Which one of the following is a communication pathway connecting transmitting signals in binary digits between two or more devices?
A. Memory
B. Register
C. CPU
D. Bus
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
The common bus is a set of shared lines used to transfer binary information among registers (PDF p.40). The structural definitions distinguish storage and processing components from their communication mechanism (p.6).
Evidence in the complete study note
A bus is a set of common signal lines used to transfer binary information among connected units.COA-S02
The CPU contains an ALU, control unit and registers; a microcontroller is a complete integrated control system, not another mandatory CPU subunit.COA01
Choice by choice
A · incorrect — Main memory stores data; it is an endpoint (p.6).
B · incorrect — Registers store bits, rather than naming the pathway (p.35).
C · incorrect — CPU processes and controls; it is a communicating component (p.6).
D · correct — A bus supplies common bit lines and selection controls (p.40).
Question 3
Which memory is characterized by the need for periodic change in order to maintain data storage?
A. Static RAM
B. Dynamic RAM
C. Disk
D. Tape
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Interpret “periodic change” as periodic charge refreshing: capacitor charge leaks, so DRAM needs refresh (PDF p.80). This is different from SRAM power retention and nonvolatile secondary storage (p.91).
Evidence in the complete study note
SRAM uses powered bistable storage: fast and costly per bit, without periodic refresh.COA24
DRAM stores charge and requires refresh: denser and commonly used for main memory.COA24
It does not need continuous power to preserve stored bits.COA28
Choice by choice
A · incorrect — SRAM uses flip-flops and holds data while powered (p.80), without the stated charge refresh.
B · correct — DRAM capacitor discharge explicitly requires periodic refreshing (p.80).
C · incorrect — Disk is nonvolatile secondary storage (p.91), not capacitor-refresh RAM.
D · incorrect — Tape is also nonvolatile secondary storage (p.91), not refresh RAM.
Question 4
In the ordinary HDD model, which statement is incorrect? Read/write refers to accessing sectors on the current track; seeking to another track is a separate operation.
A. Data is arranged in sectors within tracks
B. The head stays over the selected track while its sectors rotate beneath it
C. Its data is organized in tracks
D. It needs continuous power to keep bit contents
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: D — It needs continuous power to keep bit contents
An HDD records magnetic patterns in sectors arranged on tracks. During access to a selected track, rotation brings sectors under the head; seeking moves the head radially to another track. The medium retains its magnetic contents without continuous power, so the claimed power requirement is false. Power is needed to operate the drive, but that differs from power needed merely to retain the stored bits.
Evidence in the complete study note
An HDD stores magnetic patterns on tracks divided into sectors; reads/writes access addressed blocks while platters rotate.COA28
A head normally stays over a track while reading but moves radially for seeks.COA28
It does not need continuous power to preserve stored bits.COA28
Choice by choice
A · incorrect — Sectors are subdivisions of tracks in the stated HDD organization.
B · incorrect — This describes track-local access; a separate seek changes which track is under the head.
C · incorrect — Magnetic disk data is organized on tracks, so this statement is true.
D · correct — An HDD is nonvolatile: retaining stored patterns does not require continuous power.
Question 5
Which listed circuit category requires stored state so that output can depend on past input behavior as well as present inputs?
A. Combinational circuit
B. Sequential circuits
C. A two-input AND gate with no feedback
D. A combinational multiplexer with no storage
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
A sequential circuit contains state that preserves information about prior behavior. A combinational circuit computes its outputs from current inputs after propagation delay. The specified AND gate and multiplexer are combinational examples without storage or feedback. They therefore do not require remembered state, while the sequential-circuit category does. This distinction concerns logical state, not whether physical propagation takes time.
Evidence in the complete study note
A combinational output depends on present inputs after propagation delay.COA05
Adders, multiplexers, demultiplexers, encoders and decoders have no stored logical state.COA05
A sequential circuit depends on stored state as well as inputs; registers, counters and flip-flops are examples.COA05
AND is 1 only when all inputs are 1; OR is 1 if any input is 1.COA03
Choice by choice
A · incorrect — Combinational output depends on current inputs rather than stored history.
B · correct — Sequential circuits retain state and can make output depend on past behavior.
C · incorrect — The specified AND gate computes a truth function of its present inputs without storage.
D · incorrect — The specified multiplexer selects a present data input; it has no stored logical state.
Question 6
In computers, subtraction is carried out generally by __________.
A. 1's complement method
B. 2's complement method
C. Signed magnitude method
D. BCD subtraction method
Hint / Module Reference (Where to Read)
Keep the radix, bit width and representation fixed; evaluate place values or arithmetic steps in order.
Subtraction is described as complementation plus addition: add one to the inverted subtrahend, then add that two’s complement to the minuend (PDF p.42). Hence R1 + (~R2+1) represents R1−R2 within the register width.
Evidence in the complete study note
Compute A−B as A+(two’s complement of B), retaining n result bits.COA09
Choice by choice
A · incorrect — One’s complement alone omits the added 1 in p.42’s subtraction procedure.
B · correct — The inversion-plus-one subtrahend is exactly two’s complement (p.42).
C · incorrect — The cited procedure does not use separate sign and magnitude arithmetic.
D · incorrect — The cited general register subtraction is not BCD digit subtraction.
Question 7
Pick the different _
A. Decoder
B. Encoder
C. Multiplexer
D. Shift Register
Hint / Module Reference (Where to Read)
Check whether output depends only on current inputs or also on stored state, and track the stated clock behavior.
Correct answer: D — Shift register: the sequential circuit.
COA05 distinguishes combinational circuits from sequential storage. Decoder, encoder and multiplexer are explicitly combinational; the shift register retains state and therefore belongs to the sequential class. The image confirms the four option texts. Using the state criterion provides the technically supported odd-one-out distinction without relying on the source emphasis.
Evidence in the complete study note
A combinational output depends on present inputs after propagation delay.COA05
A sequential circuit depends on stored state as well as inputs; registers, counters and flip-flops are examples.COA05
Choice by choice
A · incorrect — A decoder is combinational and has no stored logical state in this circuit classification.
B · incorrect — An encoder is also combinational, grouping it with the decoder and multiplexer.
C · incorrect — A multiplexer selects among present inputs and is explicitly a combinational circuit.
D · correct — A shift register retains and shifts stored state, distinguishing it from the three combinational devices.
Question 8
An operation performed on the contents of a register is known as
A. Instruction code
B. Micro-operation
C. Accumulator
D. Register
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
An elementary operation on information stored in one or more registers is explicitly defined as a micro operation (PDF p.38). An instruction code tells the computer what operation to execute, while registers are the storage objects (pp.35,47).
Evidence in the complete study note
A microoperation is one elementary operation on register contents.COA11
An opcode specifies the operation; operand fields locate data or registers, and a mode field explains interpretation.COA16
Choice by choice
A · incorrect — An instruction code specifies work; it is not the elementary register operation itself (p.47).
B · correct — Matches the exact definition and examples shift, count, clear, load (p.38).
C · incorrect — Accumulator denotes a processing register, not the operation.
D · incorrect — A register stores the information being operated on (p.35).
Question 9
Which one is true about RISC computers?
A. RISC are with few numbers of registers when compared to CISC
B. RISC use complex and efficient machine instructions when compared to CISC
C. RISC is with hardwired control unit with pipelining processing
D. RISC uses extensive addressing capabilities for memory operations
E. None
Hint / Module Reference (Where to Read)
Compare textbook design tendencies without turning them into guarantees about every processor.
Correct answer: C — RISC is with hardwired control unit with pipelining processing
RISC characteristics explicitly include hardwired control, many registers, few addressing modes and an efficient pipeline (PDF p.77). These jointly support C and contradict the reversed CISC-like descriptions.
Evidence in the complete study note
The textbook RISC design pairs a relatively large register set, load/store access and easily decoded instructions with hardwired rather than microprogrammed control and an efficient pipeline.COA-S04
CISC commonly supplies more complex operations, richer addressing modes and variable lengths.COA20
Choice by choice
A · incorrect — A reverses the relatively large register count on p.77.
B · incorrect — Complex instructions are the CISC characteristic (p.78), whereas RISC has few, easily decoded instructions (p.77).
C · correct — Both hardwired control and efficient pipeline are explicitly listed (p.77).
D · incorrect — RISC has relatively few addressing modes and memory access limited to loads/stores (p.77).
E · incorrect — C is supported, so “None” fails.
Question 10
Which of the following is not a basic element within the microprocessor?
A. Microcontroller
B. Arithmetic logic unit (ALU)
C. Register array
D. Control unit
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
The module divides the CPU into the register set, ALU and control unit (PDF p.57). Treating microprocessor as the CPU implementation, A is the only choice outside that list; the module does not separately define microcontrollers.
Evidence in the complete study note
The CPU contains an ALU, control unit and registers; a microcontroller is a complete integrated control system, not another mandatory CPU subunit.COA01
Choice by choice
A · correct — Microcontroller is not one of the three CPU components listed on p.57.
B · incorrect — ALU performs the micro-operations (p.57).
C · incorrect — The register set stores intermediate data (p.57).
D · incorrect — Control unit supervises transfers and ALU operations (p.57).
Question 11
After CPU setup, which transfer method moves a block between an I/O device and memory without the CPU copying each data word?
A. Software interrupts
B. Interrupt-driven I/O
C. Polled I/O
D. Direct memory access (DMA)
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
DMA assigns the block movement to a controller after the CPU configures the transfer. Polling and ordinary interrupt-driven I/O still make the CPU execute item transfers. A software interrupt is an instruction-requested control transfer to a handler, not a block-copy engine. CPU setup and completion handling remain part of DMA; bypass refers specifically to avoiding CPU copying for every word.
Evidence in the complete study note
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
A software interrupt is deliberately requested by an instruction.COA19
Choice by choice
A · incorrect — A software interrupt requests handler execution; it does not itself move a block directly between device and memory.
B · incorrect — The interrupt handler still uses CPU execution to service the device and move items.
C · incorrect — The CPU checks status and moves items itself in polled I/O.
D · correct — The DMA controller performs the block transfer after setup, avoiding per-word CPU copies.
Question 12
In the simple CPU-master bus model, which bus carries instruction or operand values in both directions during memory reads and writes?
A. Address bus
B. Control bus
C. Data bus
D. None of the above
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Data signals carry the values transferred between processor and memory. A read brings those values toward the CPU, while a write sends them toward memory, so the data bus serves both directions. Address signals select a location. Control signals coordinate operations and can include signals in both directions, but the question specifically asks about instruction or operand values rather than aggregate control direction.
Evidence in the complete study note
Address signals select a location; data signals carry values; control signals coordinate read/write, timing, requests and acknowledgements.COA12
In the simple CPU-master model, addresses flow from CPU to memory, while data travels in either direction.COA12
Choice by choice
A · incorrect — The address bus selects locations rather than carrying payload values.
B · incorrect — Control signals coordinate transfers rather than carrying the instruction or operand payload.
C · correct — The data bus carries values toward the CPU on reads and toward memory on writes.
D · incorrect — The data bus supplies the requested role.
Question 13
Which specific instruction-processing technique overlaps fetch or decode of a later instruction with execution of an earlier instruction?
A. Superscalar processing
B. None of the above
C. Parallel Computation
D. Pipe-lining
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Fetching or decoding one instruction while another is being executed overlaps different instruction stages, which is pipelining. Superscalar processing instead permits issuing multiple instructions to execution resources during a cycle. These techniques can coexist, but the specific fetch/decode-versus-execute overlap identifies the pipeline mechanism rather than the processor’s issue width.
Evidence in the complete study note
“Fetch/decode one instruction while executing another” describes pipelining, whereas issuing several instructions in one cycle requires multiple-issue resources.COA35
Superscalar execution issues multiple instructions to multiple functional units in a cycle when dependencies permit.COA36
Choice by choice
A · incorrect — Superscalar processing names multiple-issue execution resources; the stated overlap of different stages specifically describes pipelining.
B · incorrect — Pipelining is an available matching choice.
C · incorrect — Parallel computation is broader simultaneous processing (p.114); it does not identify the staged instruction mechanism as precisely as D.
D · correct — The instruction pipeline reads consecutive instructions while previous ones execute (p.117).
Question 14
Which instruction class, where supported, bypasses the immediately following instruction when its condition is met?
A. Branch instruction
B. Return instruction
C. Skip instruction
D. Jump instruction
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
A SKIP instruction conditionally bypasses the next instruction. That differs from an ordinary branch, which chooses a target, and from RETURN, which restores a saved return point. The original phrase jump to the next instruction did not express bypassing it; the revised wording states that intended control-flow effect precisely. The classification is based on behavior rather than an unstated machine-specific opcode.
Evidence in the complete study note
Branch instructions choose a target, conditionally or unconditionally.COA19
CALL saves a return point; RETURN restores it.COA19
SKIP, where supported, bypasses the next instruction when its condition holds.COA19
Choice by choice
A · incorrect — A branch chooses a target rather than naming the specific next-instruction-bypass class.
B · incorrect — RETURN restores a saved return point.
C · correct — SKIP is the conditional next-instruction-bypass operation described.
D · incorrect — A general jump chooses a target rather than naming this specific conditional operation.
Question 15
An interrupt that is caused by register overflow, attempt to divide by zero, an invalid
operation code, stack overflow can be?
A. None of the above
B. Software interrupt
C. External interrupt
D. Internal interrupt
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: D — Internal interrupt (synchronous exception).
COA19 classifies divide errors and illegal opcodes as synchronous internal exceptions because they arise from the executing instruction. Register or stack overflow belongs to that category when the machine traps it. Overflow does not invariably interrupt: ordinary flags may merely record it. Deliberate software requests and asynchronous external device events describe different causes.
Evidence in the complete study note
External interrupts arise from devices or timers; synchronous internal exceptions arise from the executing instruction, such as divide errors, illegal opcodes or access violations.COA19
A software interrupt is deliberately requested by an instruction.COA19
Arithmetic overflow trapping depends on architecture and instruction; ordinary overflow flags need not trigger an interrupt.COA19
Choice by choice
A · incorrect — The internal-exception category directly covers these instruction-related faults when trapping is enabled.
B · incorrect — A software interrupt is deliberately requested by an instruction, rather than caused by an execution fault.
C · incorrect — External interrupts originate from devices or timers, rather than the faulting instruction.
D · correct — These execution-generated faults are internal exceptions; overflow trapping still depends on the architecture.
Question 16
Computer address bus is
A. Unidirectional
B. None of the above
C. Multidirectional
D. Bidirectional
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
For the CPU-initiated memory operations described, CPU-held address registers supply the memory address (PDF pp.82–83 and 70). Thus the address path runs CPU→memory; this is a direction within that model, not a rule excluding DMA bus masters.
Evidence in the complete study note
In the simple CPU-master model, addresses flow from CPU to memory, while data travels in either direction.COA12
Choice by choice
A · correct — CPU loads MAR to select memory; the addressed memory does not return an address (pp.82–83).
B · incorrect — The described CPU-address path supplies a matching option A.
C · incorrect — The module’s CPU-memory operation does not require simultaneous multidirectional address flow.
D · incorrect — Read/write data can go both ways, but the initiating CPU supplies the address.
Question 17
The simplest way to organize a computer is to have one processor register and an
instruction code format with two parts. The first part specifies the operation to be performed and
the second specifies .
A. address
B. output
C. Input
D. operand
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The module reproduces this two-part instruction description: operation first, address second; that address locates the operand (PDF p.47). The operand itself and its address must not be conflated.
Evidence in the complete study note
In the textbook single-accumulator organization, a memory-reference instruction has an operation part and an address part.COA-S03
The address locates a memory operand; the operation combines that operand with the accumulator as required.COA-S03
Choice by choice
A · correct — The second field specifies an address (p.47).
B · incorrect — Output is not the second field in this format.
C · incorrect — Input is not the second field in this format.
D · incorrect — The operand is fetched using the address; it is not generally embedded in this field (p.47).
Question 18
Which of the following computer memory is fastest?
A. RAM
B. Register
C. None of the above
D. Hard disk
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
The hierarchy figure on PDF p.79 places registers before cache, RAM and disk. Register organization also avoids time-consuming memory accesses (p.58). Although p.84 calls cache the fastest memory-hierarchy component, it qualifies cache as approaching CPU component speed; registers are the CPU storage meant here.
Evidence in the complete study note
A usual speed/cost-per-bit order is registers, L1/L2/L3 cache, DRAM, SSD, HDD and archival tape.COA23
Choice by choice
A · incorrect — RAM requires memory access, avoided by retaining intermediate values in registers (p.58).
B · correct — Registers are the fastest offered CPU storage tier in Figure 6.1 (p.79).
C · incorrect — A listed choice fits.
D · incorrect — Disk lies at the slow, large secondary-storage end of the hierarchy (p.79).
Question 19
It is a method used to synchronize the I/O device with the microprocessor
A. Interrupt
B. Handshaking
C. Interface
D. None
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
COA31 describes asynchronous handshaking as an exchange of request/ready and acknowledgement signals. The sender presents data, the receiver accepts it, and the feedback coordinates transfer despite unequal device and processor speeds. An interrupt requests service but does not itself name this two-sided transfer protocol. An interface is the broader connection exposing the signals and registers.
Evidence in the complete study note
Asynchronous handshaking uses request/ready and acknowledgement signals to tolerate unequal speeds: sender presents data and requests, receiver accepts and acknowledges, then each withdraws its signal.COA31
A single strobe lacks this feedback.COA31
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
Choice by choice
A · incorrect — Interrupts request processor attention; they do not specifically identify the request-and-acknowledgement transfer protocol.
B · correct — Request and acknowledgement signals synchronize the sender and receiver despite unequal operating speeds.
C · incorrect — An interface provides the connection; handshaking names the synchronization method implemented through it.
D · incorrect — Handshaking is an explicitly supported synchronization method, so an affirmative option fits.
Question 20
Which one of the following instructions is incorrect?
A. MOV AL, BP
B. INC CX
C. DEC CX
D. All
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Under the ordinary Intel forms specified in COA22, AL is an 8-bit destination while BP is a 16-bit source. MOV does not implicitly resize these operands, so MOV AL, BP is invalid. INC CX and DEC CX are legal 16-bit operations. Consequently the all-invalid alternative fails because two listed instructions are valid.
Evidence in the complete study note
MOV AL,BP is invalid because operand widths differ (8 versus 16 bits).COA22
INC CX and DEC CX are valid word operations.COA22
Choice by choice
A · correct — The 8-bit AL and 16-bit BP widths do not match for this MOV instruction.
B · incorrect — INC CX legally increments a 16-bit register under the stated legacy x86 assumptions.
C · incorrect — DEC CX legally decrements a 16-bit register under the stated legacy x86 assumptions.
D · incorrect — INC CX and DEC CX are valid, so the instructions are not all incorrect.
Question 21
A register used to indicate the condition of the microprocessor is
A. SI
B. FLAG
C. DI
D. EIP
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
COA21 states that FLAGS/EFLAGS/RFLAGS report processor status. This is the register family indicated by the option FLAG. SI and DI are general-purpose registers with conventional index roles, and EIP identifies the instruction position. Neither the index registers nor the instruction pointer is the processor condition/status register requested.
Correct answer: D — None of these immediate-to-segment MOV forms is valid.
COA22 excludes a direct immediate-to-segment-register MOV in the assumed legacy x86 syntax. DS, ES and SS are segment registers, and each listed source is an immediate number. A permitted sequence first loads the value into a suitable general register and then moves that register to the segment register. Therefore all three displayed forms fail.
Evidence in the complete study note
Segment-register MOV has register/memory forms, not a direct immediate-to-segment form: load an immediate into AX, then MOV DS,AX.COA22
Choice by choice
A · incorrect — MOV DS, 20 attempts the unsupported direct transfer of an immediate into a segment register.
B · incorrect — MOV ES, 40 also attempts an unsupported immediate-to-segment-register transfer in the stated syntax.
C · incorrect — MOV SS, 60 has the same unsupported direct immediate source for a segment destination.
D · correct — All three proposed segment-register instructions require an intermediate register or supported memory source.
Question 23
A register used to address the next instruction in a section of memory is
A. RSP
B. CS
C. RIP
D. SS
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
COA21 identifies IP/EIP/RIP as the instruction-position register family; COA14 identifies the PC role as locating the next instruction to fetch. RIP is the corresponding 64-bit x86 instruction pointer. CS selects the code segment and SS the stack segment, while RSP is the stack pointer. A segment selector alone does not identify the next instruction offset.
Evidence in the complete study note
In Intel 64-bit mode, RIP holds the offset of the next instruction to execute.COA-S05
RSP is the 64-bit stack pointer, extending the ESP/SP stack role.COA-S05
These pointers are distinct from CS and SS, which are code and stack segment registers.COA-S05
Choice by choice
A · incorrect — RSP tracks the stack, not the next instruction position within the instruction stream.
B · incorrect — CS identifies the code segment; the instruction pointer supplies the instruction position within it.
C · correct — RIP is the x86 instruction pointer used to identify the next instruction position.
D · incorrect — SS identifies the stack segment rather than the location of the next instruction.
Question 24
The Intel's first true 32-bit microprocessor is
A. Pentium
B. 80486
C. 80286
D. 80386
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
Correct answer: D — 80386, within the offered x86 lineage.
COA38 explicitly dates 32-bit x86 execution to the 80386 in 1985. It precedes the 80486 and Pentium, while the 80286 is a 16-bit predecessor. The offered choices therefore select 80386. This conclusion concerns the x86 sequence represented by the options; it should not be expanded into a claim about every historical Intel processor family.
Evidence in the complete study note
Intel’s 80386 introduced 32-bit x86 execution in 1985, before 80486/Pentium; the 80286 was a 16-bit predecessor.COA38
Choice by choice
A · incorrect — Pentium follows the 80386; it was not the first 32-bit member among these x86 choices.
B · incorrect — The 80486 follows the 80386, which had already introduced 32-bit x86 execution.
C · incorrect — The note identifies the 80286 as a 16-bit predecessor, rather than the 32-bit introduction.
D · correct — The 80386 introduced 32-bit x86 execution before the other offered 32-bit processors.
Question 25
The content of BH is 10, AL is 8, CL is 4 how much is the content of AX after MUL BH
A. 40
B. 80
C. 32
D. 320
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The operand BH is a byte register. COA22 states that unsigned byte MUL multiplies AL by the explicit byte operand and stores the product in AX. Substituting the given values yields 8 × 10 = 80. CL is not an operand of MUL BH; multiplying by its value would change the instruction being evaluated.
Evidence in the complete study note
Unsigned MUL with a byte operand multiplies AL by that byte and writes AX.COA22
Thus AL=8 and BH=10 gives AX=80 after MUL BH; CL is irrelevant.COA22
Choice by choice
A · incorrect — 40 multiplies BH by CL, but byte MUL uses AL as its implicit multiplicand.
B · correct — AL × BH equals 8 × 10 = 80, written into AX.
C · incorrect — 32 multiplies AL by CL, whereas the explicit operand is BH, not CL.
D · incorrect — 320 incorrectly includes CL as a third factor; MUL BH multiplies only AL and BH.
Question 26
Which legacy x86 instruction is arithmetic rather than a data-transfer or operand-exchange operation?
A. MOVS
B. LODS
C. XCHG
D. INC
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
MOVS and LODS are string-transfer operations, and XCHG exchanges operand values. INC instead increments an operand, making it arithmetic. The revised stem states the classification criterion, so different no longer depends on whether the reader groups string operations, operand counts or another property. This retains the original instruction set and intended comparison while giving every choice a definite classification.
Evidence in the complete study note
MOVS and LODS are string transfer operations, XCHG exchanges operands, and INC is arithmetic.COA22
Choice by choice
A · incorrect — MOVS transfers string data.
B · incorrect — LODS loads string data.
C · incorrect — XCHG exchanges operands rather than performing arithmetic.
D · correct — INC increments an operand arithmetically.
Question 27
Which register is a user-accessible register?
A. DX
B. IR
C. MBR
D. MDR
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
COA21 explicitly identifies DX as programmer-visible and IR/MDR as conceptual internal registers. MBR is the memory-buffer name used for the same data-transfer role as MDR in COA11. The question asks which register is user-accessible in this architectural sense, so the x86 general-purpose register DX is the supported choice.
Evidence in the complete study note
DX is programmer-visible; IR/MDR are conceptual internal registers.COA21
A read places an address in MAR/AR, asserts read, waits for memory and captures data in MDR/MBR/DR.COA11
Choice by choice
A · correct — DX belongs to the programmer-visible x86 register set and is usable by ordinary instructions.
B · incorrect — IR is the conceptual internal instruction register, rather than an ordinary programmer-addressable register.
C · incorrect — MBR is the internal memory-buffer/data-transfer register, not a user-visible general-purpose register.
D · incorrect — MDR is the conceptual internal memory-data register, not an ordinary user-accessible execution register.
Question 28
Which register is found starting from Pentium processor?
A. EAX
B. EIP
C. R8
D. None
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: D — None was introduced with original Pentium.
Reading starting from as introduced with Pentium, COA21 rules out every named register. EAX and EIP already existed with the 80386, while R8 belongs to the later 64-bit extension rather than original Pentium. Therefore none is correct under the introduction-date reading. Simply asking which registers a Pentium contains would be a different question, with EAX and EIP both present.
Evidence in the complete study note
EAX/EIP existed with the 80386, before Pentium; R8–R15 belong to the 64-bit extension, not original Pentium.COA21
Choice by choice
A · incorrect — EAX existed before Pentium in the 80386; it was not introduced starting with Pentium.
B · incorrect — EIP also existed in the 80386, so Pentium was not its first generation.
C · incorrect — R8 belongs to the later 64-bit extension, not the original Pentium register set.
D · correct — None of the named registers was introduced with original Pentium under the starting-generation reading.
Question 29
How many physical processor cores does the Intel Core i7-920 desktop processor have? Count cores, not hardware threads.
A. 5
B. 4
C. 6
D. 7
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
The supplementary Intel desktop-processor comparison chart specifies four cores and eight threads for the i7-920. The answer is therefore four physical cores. The supplied note provides related background that Core i7 is a family with no single core count, but does not supply this model’s number. Naming the model and consulting Intel supplies that missing fact without implying that every Core i7 has the same configuration.
Evidence in the complete study note
Intel’s desktop comparison chart lists the Core i7-920 with four physical cores and eight hardware threads.COA-S01
Additional authoritative reference
Intel lists four physical cores and eight hardware threads for the i7-920.
In direct addressing, the instruction’s address field is itself the effective address: EA=A, and the operand is M[A]. Immediate addressing uses A as a value rather than a memory address, while register addressing uses a register as the operand source. A transfer’s register and memory endpoints alone do not determine its addressing mode, so the revised question supplies the missing effective-address relationship.
Evidence in the complete study note
Immediate uses value A; direct uses EA=A and operand M[A]; indirect uses EA=M[A] then operand M[EA].COA18
Choice by choice
A · correct — EA=A defines direct addressing.
B · incorrect — Immediate addressing uses A as the operand value.
C · incorrect — Register addressing uses a register operand rather than M[A].
D · incorrect — Direct addressing matches the relationship.
Question 31
One of the following is not a characteristic of SRAM
A. Fast
B. Expensive
C. Memory refreshing s
D. None
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
SRAM stores bits in flip-flop state; applying power is sufficient and no refresh is needed (PDF p.81). Fast and relatively expensive are expressly listed, making refreshing the exception.
Evidence in the complete study note
SRAM uses powered bistable storage: fast and costly per bit, without periodic refresh.COA24
DRAM stores charge and requires refresh: denser and commonly used for main memory.COA24
Choice by choice
A · incorrect — Faster than DRAM is stated (p.81).
B · incorrect — More expensive than DRAM is stated (p.81).
C · correct — No need for refreshing is explicit (p.81), so this is the non-characteristic.
D · incorrect — There is a non-characteristic, C.
Question 32
Which one of the following is analog to digital converter?
A. ADC080X
B. DAC0830
C. 82C55
D. None
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Correct answer: A — ADC080X is the analog-to-digital converter.
COA33 defines an ADC as producing a digital code from an analog input and specifically identifies ADC080x as an 8-bit successive-approximation ADC family. DAC0830 performs the reverse conversion. The 82C55 is a programmable parallel I/O interface, not an ADC. The component identifiers therefore resolve this question without inferring capabilities merely from their general interface role.
Evidence in the complete study note
An ADC measures an analog input and produces a digital code; a DAC produces an analog output from a digital code.COA33
ADC080x parts are 8-bit successive-approximation analog-to-digital converters; DAC0830 is a digital-to-analog converter, while 82C55 denotes a programmable parallel I/O interface, not an ADC.COA33
Choice by choice
A · correct — ADC080x is explicitly identified as the analog-to-digital converter family in the note.
B · incorrect — DAC0830 converts digital codes into analog output, which is the reverse direction.
C · incorrect — 82C55 provides programmable parallel I/O; the note explicitly distinguishes it from an ADC.
D · incorrect — ADC080X is a valid analog-to-digital component, so the list is not missing an answer.
Question 33
Which is NOT an Intel x86 16-bit general-purpose register?
A. AX
B. BP
C. SI
D. FLAGS
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Intel’s general-purpose classification includes AX, BP and SI even though these registers have conventional special roles. FLAGS instead reports status conditions and is outside that group. The final option supplies an actual non-general-purpose register rather than incorrectly excluding SP merely because it tracks the stack. This preserves the register-class distinction without inventing a narrower meaning for multipurpose or misrepresenting Intel’s classification.
Evidence in the complete study note
In Intel x86 notation, AX/BX/CX/DX, BP/SP and SI/DI are 16-bit general-purpose registers, with conventional special roles.COA21
Correct answer: D — All listed categories are forms of computer design/architecture in the broad wording.
COA01 calls microarchitecture the internal processor design, while COA02 contrasts Harvard and Von Neumann memory organizations. The broad phrase type of computer architecture encompasses all three usages, although they describe different abstraction levels. The comprehensive answer is therefore all of the mentioned. No single named option covers the entire set of valid architectural categories.
Evidence in the complete study note
Microarchitecture names the internal processor design.COA01
In the textbook Von Neumann model, instructions and data share an addressed memory system; the CPU normally advances sequentially unless control flow changes.COA02
Harvard separates instruction and data memories or paths.COA02
Choice by choice
A · incorrect — Microarchitecture is a valid internal-design category, but this alone omits the two valid memory organizations.
B · incorrect — Harvard is a valid architecture category, but selecting it alone excludes the other valid categories.
C · incorrect — Von Neumann is valid, but the broad question also admits microarchitecture and Harvard organization.
D · correct — All three names describe architectural design categories, though they operate at different abstraction levels.
Question 35
Which one is not a combinational circuit?
A. Encoder
B. Decoder
C. Multiplexer
D. De-multiplexer
E. Register
Hint / Module Reference (Where to Read)
Check whether output depends only on current inputs or also on stored state, and track the stated clock behavior.
A register is a group of state-holding flip-flops (PDF p.35). Sequential circuits retain past information (p.15), whereas code/routing combinational circuits transform current inputs (pp.31,33–34). Thus register is the non-combinational choice.
Evidence in the complete study note
A combinational output depends on present inputs after propagation delay.COA05
A sequential circuit depends on stored state as well as inputs; registers, counters and flip-flops are examples.COA05
Choice by choice
A · incorrect — Encoder maps the active input into a binary code (p.34); no stored state is part of this described mapping.
B · incorrect — Decoder selects an output based on the input pattern (p.33).
C · incorrect — Multiplexer is explicitly combinational (p.31).
D · incorrect — Demultiplexer routes one input to a selected output (p.33), a present-input routing function.
E · correct — Register contains storage flip-flops and retains state (p.35).
Question 36
In a _________ cache organization, cache permits data to be stored in any cache
block.
A. Direct Mapped
B. Set Associativity
C. Fully Associative
D. All
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Associative cache stores an address with each data item and searches by content (PDF p.87), rather than constraining a block to a single index. Set association retains index constraints (p.88). Fully associative is therefore the any-block placement organization.
Evidence in the complete study note
Direct mapping uses line=block mod L.COA25
Fully associative placement permits any line.COA25
A W-way set-associative cache has S=L/W sets and set=block mod S; any of W ways in that set may hold the block.COA25
Choice by choice
A · incorrect — Direct mapping has fixed index conflicts (p.88), so does not allow arbitrary block placement.
B · incorrect — Set association allows multiple entries under the same index, not any block anywhere (p.88).
C · correct — Address/content pairs searched associatively permit the unrestricted mapping described (p.87).
D · incorrect — Direct and set mappings are restricted, so not all satisfy the claim.
Question 37
Which one used to translate virtual addresses into physical addresses when we are
implementing the concept of Virtual memory?
A. LRU
B. FIFO
C. Memory Management Unit
D. All
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
COA27 states that the MMU translates virtual/logical addresses into physical addresses using page tables and often a TLB. LRU and FIFO instead choose replacement victims, as described in COA26. Neither replacement policy performs address translation. Consequently the MMU is the single component matching the requested virtual-memory translation role; the all alternative incorrectly includes two different mechanisms.
Evidence in the complete study note
The MMU translates virtual/logical addresses to physical addresses, using page tables and often a TLB of recent translations.COA27
FIFO evicts the earliest inserted line; LRU evicts the least recently accessed line.COA26
Choice by choice
A · incorrect — LRU chooses a least-recently-used replacement victim; it does not translate virtual addresses.
B · incorrect — FIFO selects the earliest inserted replacement victim, rather than computing physical addresses.
C · correct — The MMU performs virtual-to-physical address translation using the translation structures described in the note.
D · incorrect — Only the MMU translates addresses; LRU and FIFO are replacement policies.
Question 38
In a ________ bus, flow is only one-way from the CPU to memory.
A. Address Bus
B. Data Bus
C. Control Bus
D. A & C
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
In the CPU-master model, CPU address registers identify the memory location (PDF pp.82–83), while data supports reads and writes (p.105) and control/status includes messages from both sides (pp.102–103). This makes A the specific one-way address path.
Evidence in the complete study note
In the simple CPU-master model, addresses flow from CPU to memory, while data travels in either direction.COA12
Aggregate control signals include both CPU outputs and device inputs; both data and control buses can therefore be bidirectional under that scope.COA12
Choice by choice
A · correct — The CPU supplies the memory address (pp.82–83).
B · incorrect — Read and write data travel in opposite directions (p.105).
C · incorrect — Status reports return from I/O modules (p.103), so the whole control/status collection is not only CPU-outward.
D · incorrect — C is not restricted to that one direction, so the conjunction fails.
Question 39
In memory hierarchy, faster access then_________.
A. Greater cost per bit
B. Greater capacity
C. Smaller cost per bit
D. All
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
The module states the speed/cost tradeoff directly: faster access has greater cost per bit (PDF p.79). Its separate capacity bullets associate larger capacity with lower cost and slower access, rather than faster access.
Evidence in the complete study note
Faster levels are generally smaller and more expensive per bit.COA23
Choice by choice
A · correct — Exact stated speed/cost relationship (p.79).
B · incorrect — Greater capacity is associated with slower access, not the stated faster tier (p.79).
C · incorrect — Smaller cost per bit is associated with greater capacity, opposite the faster-access bullet (p.79).
D · incorrect — B and C do not match the faster-access relationship.
Question 40
Which Shift register type used to act as a delay element?
A. Serial-In Serial-Out
B. Parallel-In Serial-Out
C. Serial-In Parallel-Out
D. All
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The shift register accepts/transfers data serially and moves each bit one position per clock, emitting the rightmost bit (PDF p.36). With serial input and serial output, an n-stage register delays the stream by n shifts. This derivation identifies SISO under the usual stream-delay meaning.
Evidence in the complete study note
SISO shift registers delay serial streams; SIPO collects a word and PISO serializes a parallel word.COA13
A flip-flop stores one bit while powered.COA05
Choice by choice
A · correct — Serial input traverses storage stages to serial output, producing the clock-count delay (p.36).
B · incorrect — Parallel input/serial output serializes a loaded word; it does not preserve the incoming serial stream in the described way.
C · incorrect — Serial input/parallel output exposes the stored bits together rather than the delayed serial stream.
D · incorrect — Not all listed I/O forms implement the same serial-stream delay.
Question 41
Which one of them is a Universal Logic Gates?
A. NAND
B. Ex-OR
C. AND
D. NOT
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
Figure 1.2 on PDF p.7 gives NAND as NOT(A AND B). Tie its inputs to obtain NOT A; NAND followed by that inverter gives AND; applying NAND to inverted inputs gives OR, as can be checked against the same truth tables. Thus NAND alone can build the basic AND/OR/NOT set.
Evidence in the complete study note
NAND and NOR are each universal: feeding the same input to both inputs constructs NOT; combine complemented gates to construct AND or OR.COA04
Choice by choice
A · correct — NAND supplies inversion by tying inputs and then AND/OR by composition (p.7, Figure 1.2).
B · incorrect — XOR alone maps all-zero inputs to zero; it cannot supply the inverter required by Figure 1.2.
C · incorrect — AND alone also preserves zero and cannot produce NOT using only AND gates.
D · incorrect — NOT only complements one input; it cannot combine independent input variables into AND/OR.
Question 42
Which textbook architecture model stores instructions and data in a shared addressed memory system?
A. Microarchitecture
B. Harvard Architecture
C. Von-Neumann Architecture
D. System Design
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
The Von Neumann model uses a shared addressed memory system for instructions and data. Harvard separates instruction and data memories or paths. Microarchitecture names an internal implementation, while system design is broader than the particular stored-program memory model requested. The revised stem asks about a defining memory relationship rather than claiming that all modern computers use one exclusive organization.
Evidence in the complete study note
In the textbook Von Neumann model, instructions and data share an addressed memory system; the CPU normally advances sequentially unless control flow changes.COA02
Harvard separates instruction and data memories or paths.COA02
Microarchitecture names the internal processor design.COA01
Choice by choice
A · incorrect — Microarchitecture describes internal processor implementation.
B · incorrect — Harvard separates instruction and data memories or paths.
C · correct — Von Neumann uses the described shared addressed memory model.
D · incorrect — System design is broader than this named memory model.
Question 43
In a design connecting a processor-side bus segment to an unlike peripheral bus segment, which hardware category provides the necessary bridge or interface logic?
A. SCSI
B. PCI
C. Bus bridge/controller logic
D. Multi bus
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Unlike bus segments need bridge or controller logic to adapt their interfaces and coordinate transfers. PCI names a peripheral expansion interconnect, while SCSI names a storage connection; neither alone identifies the adapting component. Multibus names a bus rather than the requested bridge category. The revised topology and component requirement make the interface-logic choice definite without assuming a particular processor bus or expansion standard.
Evidence in the complete study note
PCI is a peripheral expansion interconnect, not a disk protocol; connecting unlike bus segments requires suitable bridge/controller logic.COA32
SATA is a storage interface; legacy IDE/PATA and SCSI represent other storage connections, while iSCSI carries SCSI commands over IP.COA32
Choice by choice
A · incorrect — SCSI is a storage-connection standard rather than a bridge component.
B · incorrect — PCI names an expansion interconnect rather than the adapting logic.
C · correct — Bridge/controller logic connects unlike bus segments.
D · incorrect — Multibus names a bus rather than the required interface component.
Question 44
Combinational circuit differ from sequential circuit primarily because
A. Combinational circuit cannot be built using logic circuit
B. The output of combinational circuit depends only on the present input, not on past
output.
C. .
Sequential circuit have no feedback while combinational circuit do
D. The combinational circuit requires clock signal, but sequential circuit do not
Hint / Module Reference (Where to Read)
Check whether output depends only on current inputs or also on stored state, and track the stated clock behavior.
Correct answer: B — The output of combinational circuit depends only on the present input, not on past
output.
Combinational output depends only on input at the current time (PDF p.10); sequential output also depends on the past and includes memory elements (p.15). This is the primary functional difference, independent of implementation speed.
Evidence in the complete study note
A combinational output depends on present inputs after propagation delay.COA05
A sequential circuit depends on stored state as well as inputs; registers, counters and flip-flops are examples.COA05
Clocked sequential circuits update at designated clock events; combinational logic does not inherently require a clock.COA05
Choice by choice
A · incorrect — The definition explicitly builds a combinational circuit from gates (p.10), contradicting A.
B · correct — B restates the present-input-only definition (p.10).
C · incorrect — Sequential circuits contain memory (p.15); reversing the feedback distinction does not match the combinational definition.
D · incorrect — The module does not make a clock mandatory for combinational logic; it defines direct current-input dependence (p.10).
Question 45
Which one of the following is the first operation or step in CPU instruction cycle?
A. Executing the instruction
B. Handling interrupt
C. .
Decoding the instruction
D. Fetching the instruction
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The listed cycle begins with fetching an instruction, then decoding, possible indirect-address access, and execution (PDF p.55). In the fetch micro-operations PC first supplies AR and memory then supplies IR.
Evidence in the complete study note
A conceptual instruction cycle fetches an instruction, decodes opcode/addressing fields, obtains operands, executes, writes results where required and checks permitted interrupts.COA15
A sample fetch is MAR←PC; MDR←M[MAR]; IR←MDR; PC←PC+instruction_length.COA15
Choice by choice
A · incorrect — Execution follows fetch and decode, rather than initiating the cycle (p.55).
B · incorrect — Interrupt handling is not the first phase in the module’s listed ordinary instruction cycle.
C · incorrect — Decoding is the second listed phase (p.55).
D · correct — Fetching is explicitly phase 1, with register transfers shown on p.55.
Question 46
Which one of the following is a computer structural component that provides for
communication among CPU, main memory and I/O?
A. System unit
B. Computer network
C. CPU
D. System interconnection
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
The structural-component list defines system interconnection as the mechanism providing communication among CPU, main memory and I/O (PDF p.6). This definition exactly matches the requested role.
Evidence in the complete study note
CPU, main memory, I/O and their interconnection are the major structural parts.COA01
A bus is a set of common signal lines used to transfer binary information among connected units.COA-S02
Choice by choice
A · incorrect — “System unit” is not the named communication component in the list on p.6.
B · incorrect — A network is not the internal mechanism named in this structural definition.
C · incorrect — CPU is one of the three communicating parties, not the interconnection itself (p.6).
D · correct — The definition of system interconnection matches the entire stem (p.6).
Question 47
is a data transfer method in computer organization and architecture that
allows an I/O device to transfer data directly to or from memory without the involvement
of the CPU.
A. Asynchronous data transfer
B. Direct Memory Access (DMA)
C. .
Interrupt-driven transfer
D. Programmed I/O transfer
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
DMA sends the block directly to/from memory and keeps CPU involvement to setup and completion (PDF pp.107–108). Asynchrony describes timing, whereas interrupt/programmed I/O still make the CPU transfer data.
Evidence in the complete study note
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
Choice by choice
A · incorrect — Asynchronous transfer describes independent clocks (p.101), not a bypass path.
B · correct — DMA words go directly to or from memory without traversing CPU (p.108).
C · incorrect — The CPU executes transfers under interrupt I/O (p.106).
D · incorrect — Programmed I/O has CPU status checks and data transfer (p.104).
Question 48
Which instruction class tests a data word or computation status and sets condition information, often without retaining an arithmetic result?
A. Test instructions
B. Branch instructions
C. All of the above
D. Data-transfer instructions
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
TEST/CMP-style instructions examine values and update condition information, often discarding an arithmetic result. Branch instructions use control-flow conditions to choose a target; data-transfer instructions copy values. Those are different roles, so the aggregate alternative cannot identify the testing class. The cleaned question retains the recognizable, image-confirmed test-instruction concept while removing displaced OCR debris.
Evidence in the complete study note
TEST/CMP examine values and set condition information, often without retaining the arithmetic result.COA19
Branch instructions choose a target, conditionally or unconditionally.COA19
A branch changes the ordinary sequential instruction path to the branch address. The module explicitly identifies the actual branch address in a branch instruction (PDF p.72), and visually inspected Table 5-2 (p.52) shows both unconditional branch and conditional skip operations. Interpret “depending on the decision” as conditional branching; it is not true that every branch must be conditional.
Evidence in the complete study note
Branch instructions choose a target, conditionally or unconditionally.COA19
Choice by choice
A · correct — True under the conditional-branch interpretation: the address field supplies the alternate target (p.72).
B · incorrect — False would deny that conditional transfers select another instruction sequence; the table’s conditional skip examples illustrate such decisions (p.52).
Question 50
Which of the following is not considered as a peripheral device?
A. CPU
B. Keyboard
C. Monitor
D. All of the above
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Peripherals are external input/output devices such as keyboard and display (PDF p.99). CPU is the central processor structural component (p.6), so it is the only offered non-peripheral.
Evidence in the complete study note
A peripheral performs input, output or storage outside the CPU’s execution core; CPU itself is not a peripheral.COA29
Input units encode external information and output units present processed results.COA29
Choice by choice
A · correct — CPU is the processor, distinct from the external I/O devices (p.6).
B · incorrect — Keyboard is explicitly a peripheral (p.99).
C · incorrect — Display/video monitor is explicitly peripheral (p.99).
D · incorrect — Keyboard and monitor are peripherals, so not all choices satisfy the negative stem.
Question 51
Which one of the following statements is not true about the application of
micro-operations?
A. Selective set operation is implemented using OR micro-operation
B. Selective clear operation clears to zero the bit in the first operand only
where there are corresponding 1's in the logical operand
C. Clear operation is implemented using Exclusive-OR Micro-operation.
D. None of the above
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Selective set uses A OR B and selective clear zeroes A where B has ones (PDF p.44). For the unqualified clear operation, XOR a register with itself: each bit x XOR x=0, as shown by the equal-input rows of Figure 1.2 on PDF p.7. Thus A–C can all be true and D answers the negative stem.
Evidence in the complete study note
To set selected bits use A OR mask; to clear them use A AND NOT(mask); to toggle use A XOR mask; to retain only selected bits use A AND mask.COA13
A XOR A clears the entire register.COA13
Choice by choice
A · incorrect — The OR expression and example for selective set are explicit (p.44).
B · incorrect — The selective-clear definition exactly states zeroing A at B=1 positions (p.44).
C · incorrect — XOR self-clear is valid because 0 XOR 0 and 1 XOR 1 both equal zero (p.7, visually checked truth table).
D · correct — None of A–C is false under self-XOR clearing, so D is the exception response.
Question 52
In textbook discussions of richer CISC instructions, which term names the distance between high-level language constructs and machine operations that those instructions may reduce?
A. Time delay
B. Semantic gap
C. Cost
D. All of the mentioned
Hint / Module Reference (Where to Read)
Compare textbook design tendencies without turning them into guarantees about every processor.
The semantic gap is the distance between high-level constructs and machine operations. Richer instructions can reduce that gap by expressing elaborate operations directly. Time and cost are separate design concerns, and neither RISC nor CISC guarantees reductions in them across implementations and workloads. The revised question ties the named gap to the supported richer-instruction discussion instead of asserting one universal purpose shared by both approaches.
Evidence in the complete study note
The semantic gap is the distance between high-level constructs and machine operations; reducing it is associated with richer instructions, not a universal shared objective of both design approaches.COA20
Choice by choice
A · incorrect — Time delay is a performance measure rather than this conceptual distance.
B · correct — Semantic gap names the high-level-to-machine-operation distance.
C · incorrect — Cost is an implementation measure rather than this gap.
D · incorrect — The question asks for one specific conceptual term.
Question 53
Which register identifies the next instruction to fetch, before its address is copied into the address register for a memory access?
A. Accumulator
B. Instruction register
C. Address register
D. Program counter
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The program counter identifies the next instruction to fetch. During fetch, that address can be copied into MAR so memory can perform the access, but MAR’s general role is the address of the current memory operation. IR holds the fetched instruction itself and the accumulator holds operands or results. Specifying next instruction and the point before copying separates PC from the later memory-access address.
Evidence in the complete study note
PC identifies the next instruction to fetch.COA14
A sample fetch is MAR←PC; MDR←M[MAR]; IR←MDR; PC←PC+instruction_length.COA15
Choice by choice
A · incorrect — The accumulator holds operands or results.
B · incorrect — IR holds the fetched instruction itself.
C · incorrect — MAR holds the current memory-access address after it is loaded.
D · correct — PC identifies the next instruction to fetch.
Question 54
Which of the following logic gates has an output value that is identical to its
input?
A. NAND
B. NOR
C. Exclusive-OR
D. Buffer
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
The enabled three-state buffer has output Y=A when control C=1 (PDF p.41). Therefore buffer preserves the input logic value. Figure 1.2 on p.7 gives the other gates’ differing two-input truth tables.
Evidence in the complete study note
An enabled buffer copies its input.COA03
AND is 1 only when all inputs are 1; OR is 1 if any input is 1.COA03
Choice by choice
A · incorrect — NAND complements AND; it is not an identity function (p.7).
B · incorrect — NOR complements OR; it is not an identity function (p.7).
C · incorrect — XOR depends on both inputs; it equals one input only under an extra fixed-zero assumption (p.7).
D · correct — An enabled buffer explicitly gives Y=A (p.41).
Question 55
From the labels RISC and CISC alone, which conclusion about processor power efficiency is justified without implementation or workload information?
A. RISC
B. Neither label alone determines power efficiency
C. IANA
D. CISC
Hint / Module Reference (Where to Read)
Compare textbook design tendencies without turning them into guarantees about every processor.
Correct answer: B — Neither label alone determines power efficiency
RISC and CISC describe instruction-set design tendencies, not universal power rankings. Power efficiency depends on implementation and the work being performed, so neither label alone establishes which processor is more efficient. The option states that supported conclusion. RISC and CISC remain unjustified blanket selections, while IANA does not supply the processor implementation or workload needed to resolve the comparison.
Evidence in the complete study note
Neither label guarantees lower power, cost or execution time.COA20
Choice by choice
A · incorrect — RISC does not guarantee greater power efficiency.
B · correct — The note rejects a guaranteed power ranking from these labels alone.
C · incorrect — This does not provide a relevant processor implementation for the comparison.
D · incorrect — CISC does not guarantee greater power efficiency.
Question 56
Which of the following is not a type of memory used in an operating
system?
A. Cache
B. RAM
C. ROM
D. Ethernet
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: D — Ethernet is a network connection, not a memory type.
COA23 describes cache as copying memory blocks near the CPU, and COA24 describes RAM technologies plus nonvolatile ROM. COA32 explicitly classifies Ethernet as connecting network devices rather than memory. Thus cache, RAM and ROM are memory-related choices, while Ethernet belongs to communications. The phrase used in an operating system does not convert a network technology into storage hardware.
Evidence in the complete study note
A usual speed/cost-per-bit order is registers, L1/L2/L3 cache, DRAM, SSD, HDD and archival tape.COA23
ROM and flash retain contents without power; erasable/programmed variants mean “ROM can never be modified” is too broad.COA24
Ethernet connects network devices; it is not memory.COA32
Choice by choice
A · incorrect — Cache stores copies of memory blocks and is a genuine level of the memory hierarchy.
B · incorrect — RAM is main-memory storage, not a communication technology excluded from the memory category.
C · incorrect — ROM is nonvolatile memory even though its normal access and modification rules differ from RAM.
D · correct — Ethernet connects network devices and is explicitly distinguished from memory in the note.
Question 57
Which of the following is not a type of storage device used in an operating
system?
A. Hard disk drive (HDD)
B. Solid-state drive (SSD)
C. Tape drive
D. Ethernet cable
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: D — Ethernet cable is a communication medium.
COA28 describes HDD magnetic storage, SSD nonvolatile semiconductor storage and tape for sequential archives. It then explicitly distinguishes an Ethernet cable as a communication medium rather than a disk or RAM. The question asks for the item outside the storage-device category, so the cable is the supported exclusion regardless of which filesystem or OS uses the other devices.
Evidence in the complete study note
An HDD stores magnetic patterns on tracks divided into sectors; reads/writes access addressed blocks while platters rotate.COA28
SSDs use nonvolatile semiconductor storage without mechanical seek.COA28
Optical media use lasers; tape is suited to sequential streaming and archives.COA28
An Ethernet cable is a communication medium, not a disk or RAM.COA28
Choice by choice
A · incorrect — An HDD stores persistent magnetic patterns in addressed blocks, so it is a storage device.
B · incorrect — An SSD stores data in nonvolatile semiconductor storage, satisfying the storage-device category.
C · incorrect — A tape drive provides sequential storage suitable for streaming and archives, so it is not excluded.
D · correct — An Ethernet cable carries communication signals rather than functioning as a persistent storage device.
Question 58
Which generation of computers used vacuum tubes as their primary electronic component?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
Correct answer: A — First generation: vacuum tubes.
Under the familiar generation convention in COA38, vacuum tubes identify the first generation. Transistors belong to the second, integrated circuits to the third, and microprocessor/VLSI-era personal computers to the fourth. This question asks for the defining electronic component in that convention, so the mapping provides a direct answer without needing exact boundary dates for every historical machine.
Evidence in the complete study note
The familiar generation convention associates first with vacuum tubes, second with transistors, third with integrated circuits and fourth with microprocessor/VLSI-era personal computers.COA38
Choice by choice
A · correct — The first generation is the conventional vacuum-tube era specified in the complete note.
B · incorrect — The second generation is associated with transistors rather than vacuum tubes as its defining component.
C · incorrect — The third generation is associated with integrated circuits rather than the vacuum-tube era.
D · incorrect — The fourth generation is associated with microprocessors/VLSI rather than vacuum tubes as its primary component.
Question 59
Which generation of computers utilized transistors for electronic circuitry?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
Correct answer: B — Second generation: transistors.
COA38 maps the second generation to transistor-based circuitry. The surrounding categories distinguish the first vacuum-tube era, third integrated-circuit era and fourth microprocessor/VLSI era. Within this conventional classification, the transistor clue therefore selects the second generation. The answer concerns the defining technology, rather than claiming transistors ceased to exist when integrated circuits appeared.
Evidence in the complete study note
The familiar generation convention associates first with vacuum tubes, second with transistors, third with integrated circuits and fourth with microprocessor/VLSI-era personal computers.COA38
Choice by choice
A · incorrect — The first generation is conventionally identified with vacuum tubes, not transistor-based circuitry.
B · correct — The note explicitly associates transistor circuitry with the second generation of computers.
C · incorrect — Integrated circuits define the third-generation category, rather than the discrete-transistor era requested here.
D · incorrect — Microprocessor/VLSI-era computers define the fourth category, rather than the transistor-generation convention.
Question 60
Under the course’s conventional generation summary, around the transition into which generation did high-level programming languages become prominent?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
The course associates high-level languages becoming prominent with the transition into the second generation. That is a conventional historical summary, rather than a claim that every language was first introduced on one sharply defined boundary. The revised verb preserves the generation-history question while avoiding an unsupported universal introduction era. The other options refer to different stages in the familiar circuitry-based chronology.
Evidence in the complete study note
High-level languages became prominent around the transition into the second; introduction dates do not fit every generation boundary.COA38
Choice by choice
A · incorrect — The note instead places prominence around the transition into the second era.
B · correct — This matches the explicitly stated historical convention.
C · incorrect — The third era is associated with integrated circuits rather than this transition.
D · incorrect — The fourth era is associated with microprocessor/VLSI personal computers.
Question 61
Which generation of computers introduced the concept of stored program architecture?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
COA38 directly places stored-program machines in the first era. The stored-program clue is different from the transistor, integrated-circuit and microprocessor clues defining later generations. Under the historical convention supplied by this note, the concept therefore belongs to the first generation, even though later computers also retained stored-program operation.
Evidence in the complete study note
Stored-program machines arose in the first era.COA38
Choice by choice
A · correct — The note explicitly places the rise of stored-program machines in the first generation.
B · incorrect — The second generation retained stored programs but is not where the note places their introduction.
C · incorrect — The third generation is the integrated-circuit era, later than the stated stored-program introduction.
D · incorrect — The fourth generation is the microprocessor era, much later than the stated first-era development.
Question 62
Which generation of computers saw the development of integrated circuits?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
Correct answer: C — Third generation: integrated circuits.
COA38 associates the third generation with integrated circuits. The first is identified by vacuum tubes, the second by transistors and the fourth by microprocessor/VLSI-era personal computers. Reading development in the question as the conventional adoption/defining-technology category gives third generation; it does not require assuming that every invention date perfectly matches textbook boundaries.
Evidence in the complete study note
The familiar generation convention associates first with vacuum tubes, second with transistors, third with integrated circuits and fourth with microprocessor/VLSI-era personal computers.COA38
Choice by choice
A · incorrect — The first-generation convention identifies vacuum tubes rather than integrated circuits as the defining technology.
B · incorrect — The second-generation convention identifies transistor circuitry, preceding the integrated-circuit generation category.
C · correct — Integrated circuits are the defining third-generation technology in the supplied historical convention.
D · incorrect — The fourth generation is the later microprocessor/VLSI category rather than the initial integrated-circuit category.
Question 63
A historical computer uses magnetic-core memory and transistor-based circuitry rather than vacuum tubes or integrated circuits. Under the conventional taxonomy, which generation describes its circuitry?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
Magnetic-core memory alone does not identify a generation because it spanned more than one era. The added circuitry condition supplies the distinguishing feature: the conventional taxonomy associates transistor-based machines with the second generation. Vacuum tubes identify the first era, integrated circuits the third and microprocessor/VLSI personal computers the fourth. This version retains the magnetic-core context and states which technology determines the classification.
Evidence in the complete study note
The familiar generation convention associates first with vacuum tubes, second with transistors, third with integrated circuits and fourth with microprocessor/VLSI-era personal computers.COA38
Magnetic-core memory spanned more than one era, so “witnessed use” cannot identify exactly one.COA38
Choice by choice
A · incorrect — First-generation circuitry uses the vacuum-tube convention.
B · correct — Transistor circuitry identifies the second generation.
C · incorrect — Third-generation circuitry uses the integrated-circuit convention.
D · incorrect — The fourth era is associated with microprocessor/VLSI systems.
Question 64
Which generation conventionally introduced integrated-circuit circuitry, contributing to improved speed and performance over earlier discrete-transistor systems?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
Several generations improved speed, so improvement alone is not a unique historical marker. The revised question identifies integrated circuits as the distinguishing technology. Under the stated convention, integrated circuits identify the third generation, following transistor-based second-generation systems. Performance improvement remains a contextual trend rather than a guarantee that every individual later machine outperformed every earlier model.
Evidence in the complete study note
The familiar generation convention associates first with vacuum tubes, second with transistors, third with integrated circuits and fourth with microprocessor/VLSI-era personal computers.COA38
Integration generally reduced individual component dimensions while capacity, density and processor performance grew; these are trends rather than guarantees for every model.COA38
Choice by choice
A · incorrect — The first era is associated with vacuum tubes.
B · incorrect — The second era is associated with discrete transistors.
C · correct — The third era is associated with integrated circuits.
D · incorrect — The fourth era is associated with microprocessor/VLSI systems.
Question 65
Which generation of computers introduced the use of microprocessors?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
Correct answer: D — Fourth generation: microprocessors.
The conventional mapping in COA38 identifies the fourth generation with microprocessor/VLSI-era computers. Vacuum tubes, transistors and integrated circuits identify the preceding first, second and third categories respectively. Thus the microprocessor clue directly selects the fourth generation under the note’s convention; the question does not ask for an exact launch date or individual processor model.
Evidence in the complete study note
The familiar generation convention associates first with vacuum tubes, second with transistors, third with integrated circuits and fourth with microprocessor/VLSI-era personal computers.COA38
Choice by choice
A · incorrect — Vacuum tubes define the first-generation convention, rather than the later microprocessor era.
B · incorrect — The transistor-based second-generation category precedes the note’s microprocessor/VLSI category.
C · incorrect — Third generation denotes integrated-circuit computers; microprocessors identify the subsequent conventional category.
D · correct — The complete note explicitly associates microprocessor/VLSI-era computers with the fourth generation.
Question 66
Which generation of computers is characterized by the development of personal computers?
A. First Generation
B. Second Generation
C. Third Generation
D. Fourth Generation
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
Correct answer: D — Fourth generation: personal computers.
COA38 groups personal computers with the fourth-generation microprocessor/VLSI era. The first three alternatives instead correspond to vacuum tubes, transistors and integrated circuits. The wording characterized by asks for that conventional defining association, so fourth generation is supported without making a universal claim that no personal or individual-use machine could exist in any earlier period.
Evidence in the complete study note
The familiar generation convention associates first with vacuum tubes, second with transistors, third with integrated circuits and fourth with microprocessor/VLSI-era personal computers.COA38
Choice by choice
A · incorrect — The first era is characterized by vacuum tubes in this convention, not microprocessor-based personal computers.
B · incorrect — The second era is the transistor category rather than the personal-computer era identified here.
C · incorrect — The third era is associated with integrated circuits rather than the note’s personal-computer category.
D · correct — The note places microprocessor/VLSI-era personal computers in the fourth-generation historical convention.
Question 67
A stack organized computer uses instruction of
A. Zero addressing
B. Two addressing
C. Index addressing
D. Indirect addressing
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
For stack arithmetic the operands are implicit on top of stack, so ADD and MUL require no address field (PDF p.69). This is the zero-address organization. PUSH/POP still use explicit addresses; the answer concerns arithmetic operation instructions.
Evidence in the complete study note
Zero-address stack ADD uses two implicit top-of-stack operands.COA16
A stack is last-in, first-out.COA17
Choice by choice
A · correct — Zero-address ADD/MUL is explicit (p.69).
B · incorrect — Two-address instructions instead explicitly name register/memory operands; stack arithmetic does not (pp.67–69).
C · incorrect — Index addressing is an effective-address mechanism, not the stack operand-count format.
D · incorrect — Indirect addressing locates an address through memory (p.72); it is not the stack arithmetic format.
Question 68
An n-bit microprocessor has -
A. No answer is correct
B. n-bit program counter
C. n-bit address register
D. n-bit instruction register
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: A — None of the named register widths necessarily follows.
COA38 explicitly states that an n-bit processor label does not force its PC, IR or address register to be n bits. Those widths concern different architectural quantities. Since the stem supplies only the processor-width label and no specific design, none of the three claimed register widths is guaranteed. The no-answer-is-correct alternative is therefore the supported response.
Evidence in the complete study note
An n-bit processor label does not force its PC, IR or address register to be n bits.COA38
Word width, data-bus width, instruction width and address width need not match.COA12
Choice by choice
A · correct — None of the three specific register-width claims is implied by the processor-width label alone.
B · incorrect — Program-counter width is not forced to equal the processor’s n-bit label in every architecture.
C · incorrect — Address-register width can differ from processor word width; n bits is not guaranteed.
D · incorrect — Instruction-register width depends on instruction encoding rather than necessarily matching the processor-width label.
Question 69
In which of the following term the performance of cache memory is measured?
A. Copy ratio
B. Data ratio
C. Hit ratio
D. Cache ratio
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Cache performance is explicitly measured by hit ratio, hits/(hits+misses), in PDF p.85. A hit means the requested word is found in cache (p.84), making this a direct measure of cache availability of requested data.
Evidence in the complete study note
Hit ratio=hits/accesses; miss ratio=1−hit ratio.COA23
Choice by choice
A · incorrect — Copy ratio is not the performance quantity defined on p.85.
B · incorrect — Data ratio is not the named hit/miss measure.
C · correct — Hit ratio and its formula are explicitly provided (p.85).
D · incorrect — “Cache ratio” is not the quantity’s stated name.
Question 70
Question number 100
What is the name of logic gate based on the following graphical symbol?
A. XOR
B. NOR
C. NAND
D. AND
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
The diagram shows an AND-shaped gate with a small output circle. This is a NAND gate; the circle indicates inversion, so F=NOT(A AND B).
Evidence in the complete study note
A bubble at a gate output indicates inversion: an AND-shaped symbol with a bubble is NAND.COA03
Choice by choice
A · incorrect — XOR uses the OR-like body with an extra input curve, unlike the source symbol (p.7).
B · incorrect — NOR uses an OR-shaped body with an output circle, not the flat-input AND body (p.7).
C · correct — The AND body plus inversion circle is NAND (p.7).
D · incorrect — AND lacks the output inversion circle visible in the question.
Question 71
An interface that has multiple lines connecting the input/output module and peripheral device
and assures multiple bits to be transferred at the same time is:
A. Bus interface
B. Parallel interface
C. One line interface
D. Serial interface
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Parallel registers read/write bits simultaneously (PDF p.35); shift registers transfer serially (p.36), and a common bus supplies a line for each bit (p.40). Multiple lines carrying bits at the same time match a parallel interface by this distinction.
Evidence in the complete study note
Serial sends bits over time; parallel transfers multiple bits on multiple lines, without guaranteeing higher real-world speed.COA31
Choice by choice
A · incorrect — A bus describes a collection of lines; it does not specify serial versus parallel transfer as precisely as B (p.40).
B · correct — Simultaneous multiple-bit transfer corresponds to the parallel operation defined on p.35.
C · incorrect — One line cannot carry the described multiple separate bit signals simultaneously in this binary-line model.
D · incorrect — Serial shifting transfers the stream sequentially rather than all bits simultaneously (p.36).
Question 72
Which one of the following is a two-level cache having an internal and external caches?
A. Multilevel cache
B. Single level cache
C. Split cache
D. Unified cache
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
A two-level hierarchy has more than one cache level, so multilevel is the matching category. COA26 distinguishes L1/L2 hierarchy levels from split/unified instruction-data organization and from internal/external placement. Describing one cache as internal and another as external does not make the pair split or unified; those terms answer a different classification question.
Evidence in the complete study note
L1/L2 describe hierarchy levels; split cache means separate instruction/data caches and unified means combined.COA26
Internal/external location is another classification, not synonymous with split/unified.COA26
Choice by choice
A · correct — Two cache levels constitute a multilevel hierarchy, regardless of their internal or external placement.
B · incorrect — Single-level cache contradicts the explicitly stated presence of two cache levels in the hierarchy.
C · incorrect — Split describes separate instruction and data caches, not an internal-plus-external level arrangement.
D · incorrect — Unified describes combined instruction/data caching, not how many internal or external levels exist.
Question 73
Which statement is NOT correct about computer architecture and organization?
A. An architecture can remain for a long time but its organization can change
B. Manufacturers offer computers with the same architecture but different organization
C. An architecture can be used for a long time encompassing different computer models
D. Different organizations cannot implement the same architecture
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
Correct answer: D — Different organizations cannot implement the same architecture
Architecture describes programmer-visible behavior, while organization describes internal implementation. Several internal implementations can preserve the same architecture, allowing it to span models and remain stable while implementation details change. The false statement denies that possibility. The other choices describe compatible consequences of the distinction, without requiring a maximum architecture lifetime or a universal implementation-change rate.
Evidence in the complete study note
Different organizations can implement the same architecture; neither definition imposes a maximum lifetime.COA01
Choice by choice
A · incorrect — Implementation can change while architecture stays stable.
B · incorrect — Different organizations can implement one architecture.
C · incorrect — One architecture can encompass different computer models over time.
D · correct — This denies the supported possibility of different implementations of one architecture.
Question 74
______ is a set of attributes that can be seen by a program and can have direct impact on the
logical execution of a program.
A. Arrangement
B. Organization
C. Flow control
D. Architecture
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
Programmer-visible attributes that directly affect logical execution are the module’s exact definition of computer architecture (PDF p.5). Organization instead comprises operational units and interconnections realizing those specifications.
Evidence in the complete study note
Architecture describes programmer-visible behavior: instructions, registers, data types, address spaces and I/O conventions.COA01
Choice by choice
A · incorrect — Arrangement is not the defined programmer-visible attribute set.
B · incorrect — Organization describes implementation units and interconnections (p.5).
C · incorrect — Flow control is a function, not the definition of this attribute set.
D · correct — Architecture exactly matches the definition and examples (p.5).
Question 75
What is the purpose of an opcode that is as indicated in the figure below?
4 bits 6 bits 6 bits
[opcode] Operant etree [| Opsrand Rates|
<_ 16 bits —ccccxxcxor
A. It holds the destination address of an operand
B. It determines the operation to be done
C. It holds the source address of an operand
D. It holds the next instruction reference
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: B — It determines the operation to be done
The inspected diagram divides 16 bits into a 4-bit opcode and two 6-bit operand references. The module defines the operation part as specifying what operation is performed (PDF p.47); reference fields identify operands rather than changing that opcode role. Four opcode bits can distinguish up to 16 operation codes.
Evidence in the complete study note
An opcode specifies the operation; operand fields locate data or registers, and a mode field explains interpretation.COA16
A 4-bit opcode permits at most 16 encodings, not necessarily 16 implemented instructions.COA16
A 6-bit operand-reference field has 64 encodings; what they designate depends on the machine.COA16
Choice by choice
A · incorrect — Destination reference belongs to an operand/address field, not the operation field (p.47).
B · correct — Operation selection is the explicit opcode definition (p.47).
C · incorrect — Source reference belongs to an operand/address field.
D · incorrect — The module tracks the next instruction through PC (p.70), not this operation field.
Question 76
Which one of the following registers holds the address of the next instruction to be fetched from
memory?
A. Memory address register
B. Memory buffer register
C. Program counter
D. Instruction buffer register
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
PC holds the address of the instruction to execute next (PDF p.70). During fetch it is copied to AR and the instruction bits then enter IR while PC increments (p.55). Thus PC is the persistent next-instruction tracker.
Evidence in the complete study note
PC identifies the next instruction to fetch.COA14
A sample fetch is MAR←PC; MDR←M[MAR]; IR←MDR; PC←PC+instruction_length.COA15
Choice by choice
A · incorrect — MAR can temporarily receive the fetch address, but PC is the register that tracks the next instruction across cycles (p.55).
B · incorrect — The module describes MDR as memory data storage (p.82), not the next-instruction address tracker.
C · correct — Directly matches the PC definition and fetch transfers (pp.55,70).
D · incorrect — An instruction buffer would hold instruction content; the module identifies IR for that role (p.48), not as the next-address tracker.
Question 77
Which one of the following is NOT an I/O command?
A. Status command
B. Output data command
C. Control command
D. Issue command
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
The module enumerates four I/O command kinds: control, test, read and write (PDF pp.104–105). “Status command” is interpreted as the test/status-query kind, and “output data” as write. “Issue” is an action performed by CPU, not one of the four command kinds.
Evidence in the complete study note
Control commands start actions, test/status commands inspect readiness or errors, read commands bring device data toward the system, and write/output commands send system data to the device.COA29
“Issue” describes sending a command, not a standard fourth command category.COA29
Choice by choice
A · incorrect — Status-query corresponds to the test command, which checks status conditions (p.104).
B · incorrect — Output data corresponds to the write command (p.105).
C · incorrect — Control command activates a peripheral and specifies its action (p.104).
D · correct — Issue is not a command category in the four-type list (pp.104–105).
Question 78
The user who programs a computer in machine or assembly language must be aware of the
following EXCEPT:
A. The register set
B. The type of data supported by the instructions
C. The analysis model
D. The memory structure
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
The machine-language programmer’s architecture includes instruction formats, addressing modes, instruction sets and register organization (PDF p.57); visible data types and memory addressing are also named (p.5). An “analysis model” is not part of that architectural list.
Evidence in the complete study note
Machine-language programming depends on the register set, supported types and memory/addressing structure.COA02
Choice by choice
A · incorrect — Register organization is explicitly part of the programmer view (p.57).
B · incorrect — Supported data representation is explicitly architectural (p.5).
C · correct — Analysis model is absent from the programmer-facing attribute list; it is the unmatched option.
D · incorrect — Memory addressing is part of the architecture (p.5), under the intended visible-memory interpretation.
Question 79
Which part of the computer system is responsible for converting machine-processed data to
formats understandable by the user?
A. Communication components
B. Output unit
C. Storage unit
D. Input unit
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Computational results must be recorded/displayed for users (PDF p.99); human-readable screen/display/printer devices provide that communication (p.100). This is the output role.
Evidence in the complete study note
Input units encode external information and output units present processed results.COA29
Choice by choice
A · incorrect — Communication devices exchange data with remote devices; the category is not specifically user-readable presentation (p.100).
B · correct — Output devices record/display computed results in meaningful form for users (p.99).
C · incorrect — Storage retains information; it is not the presentation role (p.91).
D · incorrect — Input enters programs/data into the system, the reverse direction (p.99).
Question 80
In the usual memory hierarchy, which listed tier has the shortest access latency and greatest cost per stored bit?
A. Register
B. Magnetic disc
C. Main memory
D. Cache memory
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
The usual speed and cost-per-bit hierarchy places registers above cache, main RAM and magnetic disk. Registers therefore have the shortest access latency and highest cost per bit among the choices. Faster tiers are generally smaller, so this statement does not compare the total purchase price of a complete device. Cache is fast, but remains below the register tier in this teaching hierarchy.
Evidence in the complete study note
A usual speed/cost-per-bit order is registers, L1/L2/L3 cache, DRAM, SSD, HDD and archival tape.COA23
Faster levels are generally smaller and more expensive per bit.COA23
Choice by choice
A · correct — Registers are the fastest and most costly-per-bit tier among these choices.
B · incorrect — Magnetic disk is a slower, high-capacity tier with lower cost per bit.
C · incorrect — Main memory lies below registers and cache in the usual speed/cost hierarchy.
D · incorrect — Cache is fast but below registers in the usual hierarchy.
Question 81
For a legacy internal PC disk connection using parallel ATA, which listed interface name matches that connection?
A. SCSI
B. iSCSI
C. IDE
D. USB
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
The note identifies legacy IDE/PATA as a storage connection, so IDE matches the specified parallel ATA context. SCSI is a different storage interface, iSCSI carries SCSI over IP, and USB commonly connects peripherals including external storage. Naming the legacy internal parallel interface resolves the missing era and connection-role constraints without asserting that one interface is universally standard for all PCs and all storage devices.
Evidence in the complete study note
SATA is a storage interface; legacy IDE/PATA and SCSI represent other storage connections, while iSCSI carries SCSI commands over IP.COA32
Choice by choice
A · incorrect — SCSI is a different storage-connection standard.
B · incorrect — iSCSI transports SCSI commands over IP rather than using the specified local parallel interface.
C · correct — IDE corresponds to the stated legacy PATA connection.
D · incorrect — USB is a different peripheral interconnect, not parallel ATA.
Question 82
In the simple CPU-master memory-bus model, which bus carries the values read from and written to memory?
A. Control bus
B. Data bus
C. Uni-bus
D. Address bus
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The data bus carries memory-transfer values. Reads move values from memory toward the CPU, and writes move values in the opposite direction. Address signals select a location and control signals coordinate timing and read/write operations. The revised stem asks about payload rather than bidirectionality in general, since aggregate control can also contain signals in both directions. Uni-bus names a bus arrangement rather than this payload-signal category.
Evidence in the complete study note
Address signals select a location; data signals carry values; control signals coordinate read/write, timing, requests and acknowledgements.COA12
In the simple CPU-master model, addresses flow from CPU to memory, while data travels in either direction.COA12
Choice by choice
A · incorrect — Control signals coordinate the transfers rather than carrying their values.
B · correct — The data bus carries read and write values.
C · incorrect — This is not the address/data/control payload-signal category requested.
D · incorrect — Address signals choose the memory location.
Question 83
What is the purpose of an opcode that is as indicated in the figure below?
4 bits 6 bits 6 bits
<j o bits ——___________»
A. It determines the operation to be done
B. It holds the destination address of an operand
C. It holds the next instruction reference
D. It holds the source address of an operand
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Memory-mapped I/O shares memory and device address space (PDF p.105); DMA transfers blocks directly (p.107); interrupt I/O requests CPU service when ready (p.106). They are all supported I/O mechanisms, though memory mapping is an addressing choice and the others are transfer/control techniques.
Evidence in the complete study note
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
Memory-mapped I/O assigns device registers addresses in the memory address space and uses suitable load/store operations.COA31
Choice by choice
A · incorrect — Memory-mapped I/O is explicitly described (p.105).
B · incorrect — DMA is explicitly described (p.107).
C · incorrect — Interrupt-driven I/O is explicitly described (p.106).
D · correct — All three are legitimate mechanisms under the broad “communicating” wording.
Question 85
In memory-mapped I/O, I/O devices are mapped into the:
A. Main memory address space
B. Cache memory address space
C. Virtual memory address space
D. Secondary memory address space
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Memory-mapped I/O makes devices and memory share an address space, with I/O treated like memory reads/writes (PDF p.105). The relevant address space is the memory address space, not a separate cache or secondary-storage space.
Evidence in the complete study note
Memory-mapped I/O assigns device registers addresses in the memory address space and uses suitable load/store operations.COA31
Isolated/port-mapped I/O has a separate port space and special instructions such as IN/OUT.COA31
Choice by choice
A · correct — Devices share the memory address space (p.105).
B · incorrect — The module does not map device registers into a separate cache address space.
C · incorrect — The mapping definition does not depend on a process virtual address space.
D · incorrect — Secondary-storage addresses are not the shared CPU memory addresses described on p.105.
Question 86
Which technique allows data to be transferred between an I/O device and memory without
involving the CPU?
A. Memory-mapped I/O
B. Direct memory access (DMA)
C. Interrupt-driven I/O
D. I/O polling
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
DMA transfers each word directly to/from memory without passing through CPU (PDF p.108). “Without involving” must mean during the actual word transfers, since CPU setup and completion involvement are explicit on the same page.
Evidence in the complete study note
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
DMA does not eliminate CPU involvement in configuration, ownership, address mapping or completion.COA30
Memory-mapped I/O assigns device registers addresses in the memory address space and uses suitable load/store operations.COA31
Choice by choice
A · incorrect — Memory mapping specifies how I/O is addressed, not a CPU-bypass data engine (p.105).
B · correct — DMA directly transfers the block with CPU only at beginning/end (p.108).
C · incorrect — The CPU still executes the interrupt-driven data transfer (p.106).
D · incorrect — Polling keeps CPU checking device status and doing transfers (p.104).
Question 87
Which method is used to handle I/O operations that require immediate attention from the
CPU?
A. Memory-mapped I/O
B. Direct memory access (DMA)
C. Interrupt-driven I/O
D. I/O polling
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
In interrupt-driven I/O the device requests CPU service when ready; CPU can work on other instructions until then (PDF p.106). The priority-interrupt discussion on that page services the higher-priority simultaneous request first. This matches event-driven attention, without guaranteeing zero response latency.
Evidence in the complete study note
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
Interrupt priority selects among simultaneous requests, using schemes such as polling, daisy chains or priority hardware.COA31
Choice by choice
A · incorrect — Memory mapping selects addresses and does not itself notify the CPU (p.105).
B · incorrect — DMA offloads data movement (p.107); it is not the general CPU-service notification technique.
C · correct — The device interrupts CPU requesting service when ready (p.106).
D · incorrect — Polling requires the CPU to discover readiness through repeated checks (p.104).
Question 88
Which I/O technique involves the CPU continuously checking the status of an I/O device for
data transfer completion?
A. Memory-mapped I/O
B. Direct memory access (DMA)
C. Interrupt-driven I/O
D. I/O polling
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Programmed I/O explicitly makes CPU periodically check I/O status until completion, because the module does not interrupt CPU (PDF p.104). This is the polling behavior described by D.
Evidence in the complete study note
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
Choice by choice
A · incorrect — Memory mapping is the address arrangement and does not require repeated status checks (p.105).
B · incorrect — DMA permits CPU other work while moving a block (p.108).
C · incorrect — Interrupt I/O notifies CPU when ready instead of requiring periodic checking (p.106).
D · correct — CPU checks status bits periodically until completion (p.104).
Question 89
Which standard I/O interface is commonly used in UNIX-like operating systems?
A. ASCII
B. USB
C. RS-232
D. POSIX
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
COA32 identifies POSIX as a software interface standard with open/read/write/close operations. That is the software I/O interface sense appropriate to UNIX-like operating systems. ASCII is an encoding, while USB and RS-232 describe hardware interconnect/interface roles. Their availability on a UNIX-like machine does not make them the standard OS software interface requested by the alternatives.
Evidence in the complete study note
POSIX is a software interface standard with operations such as open/read/write/close; ASCII is a character encoding.COA32
USB is a serial peripheral interconnect used by keyboards and external storage; RS-232 specifies a traditional point-to-point serial electrical/interface standard.COA32
Choice by choice
A · incorrect — ASCII defines character encoding, not the UNIX-like software interface for opening, reading and writing resources.
B · incorrect — USB is a peripheral interconnect, not the software API standard identified by this OS-level wording.
C · incorrect — RS-232 defines a serial electrical/interface standard rather than the UNIX-like software I/O API.
D · correct — POSIX specifies software interface operations including open, read, write and close for this context.
Question 90
Which listed interface is a traditional point-to-point serial electrical/interface standard?
A. USB
B. Ethernet
C. RS-232
D. HDMI
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
RS-232 specifies a traditional point-to-point serial electrical/interface standard. USB also uses serial communication, so serial alone cannot distinguish them. The revised requirement identifies the traditional point-to-point interface category rather than treating every serial link as equivalent. Ethernet connects network devices and HDMI carries digital audio and video. Their connection roles differ from the interface class requested.
Evidence in the complete study note
USB is a serial peripheral interconnect used by keyboards and external storage; RS-232 specifies a traditional point-to-point serial electrical/interface standard.COA32
HDMI carries digital video and audio.COA32
Ethernet connects network devices; it is not memory.COA32
Choice by choice
A · incorrect — USB is a serial peripheral interconnect, but not the traditional point-to-point electrical standard requested.
B · incorrect — Ethernet provides networking connectivity.
C · correct — RS-232 matches the traditional point-to-point serial interface category.
D · incorrect — HDMI carries digital audio and video.
Question 91
Which standard I/O interface is widely used for connecting external storage devices, such as
hard drives and flash drives?
A. SATA
B. USB
C. Ethernet
D. HDMI
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
COA32 explicitly describes USB as a peripheral interconnect used by external storage. This directly matches the stem’s external hard-drive and flash-drive examples. SATA is described more generally as a storage interface, Ethernet connects network devices, and HDMI carries video/audio. The external peripheral examples therefore make USB the supported conventional choice among these options.
Evidence in the complete study note
USB is a serial peripheral interconnect used by keyboards and external storage; RS-232 specifies a traditional point-to-point serial electrical/interface standard.COA32
HDMI carries digital video and audio.COA32
Ethernet connects network devices; it is not memory.COA32
Choice by choice
A · incorrect — SATA is a storage interface, but USB is the note’s explicit match for the external-peripheral examples.
B · correct — The note explicitly lists external storage among USB peripheral connections, matching the supplied examples.
C · incorrect — Ethernet connects network devices rather than being the named external hard-drive/flash-drive peripheral interconnect.
D · incorrect — HDMI carries digital video and audio, rather than providing the external-storage interface requested.
Question 92
Which listed interface is specifically a storage-drive interface, rather than a general peripheral interconnect, networking interface or audiovisual link?
A. SATA
B. USB
C. Ethernet
D. HDMI
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
SATA is specifically a storage interface. USB supplies general peripheral connectivity, Ethernet connects network devices and HDMI carries digital audio/video. The connection role distinguishes these alternatives; a vague high-speed description would not, because several interfaces can be fast in suitable versions. The question therefore asks for a storage-specific interface category without assuming that speed alone uniquely identifies it.
Evidence in the complete study note
SATA is a storage interface; legacy IDE/PATA and SCSI represent other storage connections, while iSCSI carries SCSI commands over IP.COA32
USB is a serial peripheral interconnect used by keyboards and external storage; RS-232 specifies a traditional point-to-point serial electrical/interface standard.COA32
HDMI carries digital video and audio.COA32
Ethernet connects network devices; it is not memory.COA32
Choice by choice
A · correct — SATA is the storage-specific interface in the list.
B · incorrect — USB provides a different peripheral-interconnect role.
C · incorrect — Ethernet serves networking rather than this drive connection.
D · incorrect — HDMI carries audiovisual data rather than this storage link.
Question 93
Which standard I/O interface is primarily used for audio and video transmission between
devices?
A. SATA
B. USB
C. Ethernet
D. HDMI
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
COA32 explicitly identifies HDMI as carrying digital video and audio. That directly matches the primary transmission purpose asked here. SATA serves storage, USB serves general peripherals, and Ethernet serves network connections. Other links can transport encoded media in broader systems, but the stem asks the primary interface role, for which HDMI is the specific supported choice.
Evidence in the complete study note
HDMI carries digital video and audio.COA32
USB is a serial peripheral interconnect used by keyboards and external storage; RS-232 specifies a traditional point-to-point serial electrical/interface standard.COA32
Ethernet connects network devices; it is not memory.COA32
Choice by choice
A · incorrect — SATA is identified as a storage interface rather than the primary audiovisual connection in this list.
B · incorrect — USB is a general peripheral interconnect; the note specifically assigns the audiovisual role to HDMI.
C · incorrect — Ethernet is a network connection rather than the specifically identified digital audiovisual interface.
D · correct — HDMI is explicitly described as carrying digital video and audio between devices.
Question 94
Which technique divides instruction processing into stages so that different stages work on successive instructions during the same cycle?
A. Pipelining
B. Caching
C. Superscalar architecture
D. Branch prediction
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Pipelining overlaps stages of successive instructions: one may be fetched while another is decoded or executed. Superscalar execution instead concerns issuing multiple instructions to functional units in one cycle; it can coexist with a pipeline but is not the definition of the staged organization. Caching supplies nearby copies of memory blocks, and branch prediction guesses future control flow.
Evidence in the complete study note
A pipeline overlaps stages of different instructions; it primarily improves throughput.COA35
Superscalar execution issues multiple instructions to multiple functional units in a cycle when dependencies permit.COA36
Choice by choice
A · correct — Pipelining divides processing into stages and overlaps those stages across successive instructions.
B · incorrect — Caching retains memory-block copies; it is not the staged instruction organization described.
C · incorrect — Superscalar architecture provides multiple-issue execution resources rather than defining stage overlap itself.
D · incorrect — Branch prediction guesses direction or targets, rather than dividing instruction processing into pipeline stages.
Question 95
Which technique improves the performance of a processor by storing frequently accessed
data closer to the processor?
A. Pipelining
B. Caching
C. Superscalar architecture
D. Branch prediction
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Caching keeps copies of memory blocks near the CPU, exploiting temporal and spatial locality to reduce many memory-access delays. Pipelining overlaps instruction stages, superscalar execution provides multiple-issue resources, and branch prediction guesses control flow. These mechanisms may coexist, but the stated nearby data-copy storage role specifically identifies caching.
COA36 defines superscalar execution as issuing multiple instructions to multiple functional units in a cycle when dependencies permit. This matches the multiple execution units in the stem. COA35 distinguishes that multiple-issue capability from ordinary pipelining, which overlaps stages. Caching supplies reused memory data and branch prediction speculates about control flow; neither names the multiple-issue architecture.
Evidence in the complete study note
Superscalar execution issues multiple instructions to multiple functional units in a cycle when dependencies permit.COA36
A pipeline overlaps stages of different instructions; it primarily improves throughput.COA35
Choice by choice
A · incorrect — Pipelining overlaps stages but does not by itself provide multiple-instruction issue to several execution units.
B · incorrect — Caching retains nearby copies of memory blocks rather than defining parallel instruction issue.
C · correct — Superscalar execution uses multiple functional units to issue several independent instructions in a cycle.
D · incorrect — Branch prediction guesses future control flow, rather than naming the architecture with multiple execution units.
Question 97
Which technique predicts the outcome of conditional branches to improve instruction
execution in a processor?
A. Pipelining
B. Caching
C. Superscalar architecture
D. Branch prediction
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
COA36 says branch prediction guesses a branch’s direction/target and continues speculatively, discarding work when the guess is wrong. Predicting the outcome of a conditional branch is exactly that role. Pipelining overlaps processing stages, caching retains reusable data, and superscalar execution issues several instructions; those mechanisms can coexist with prediction but do not replace its definition.
Cache is the fast memory-block-copy tier used to reduce the cost of repeated or nearby CPU accesses. Virtual memory instead supplies translated address spaces and can use backing storage for nonresident pages. Pipelining and superscalar execution organize instruction processing, so neither names the memory-hierarchy buffer requested. The answer follows the storage role rather than a general claim that only one mechanism can improve performance.
Evidence in the complete study note
A usual speed/cost-per-bit order is registers, L1/L2/L3 cache, DRAM, SSD, HDD and archival tape.COA23
Cache copies memory blocks near the CPU.COA23
Virtual memory gives processes translated address spaces and protection; backing storage can hold nonresident pages.COA27
Superscalar execution issues multiple instructions to multiple functional units in a cycle when dependencies permit.COA36
Choice by choice
A · incorrect — Pipelining divides computational tasks into stages (p.116), not memory storage levels.
B · correct — Cache supplies the fast tier in the hierarchy and avoids main-memory access on hits (pp.79,84).
C · incorrect — Superscalar execution concerns multiple instruction issue, not a memory-hierarchy storage tier.
D · incorrect — Virtual memory supplies an apparent larger memory space (p.90), not the fast-cache-hit mechanism.
Question 99
Which processor technique issues multiple independent instructions to multiple functional units in one clock cycle, when dependencies permit?
A. Pipelining
B. Caching
C. Superscalar architecture
D. Instruction-level parallelism
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Superscalar execution issues multiple instructions in a cycle when the machine has suitable resources and the instructions’ dependencies permit it. Pipelining overlaps stages of different instructions but need not issue several at once. Caching addresses memory access, while instruction-level parallelism is the broader opportunity exploited by several mechanisms. The revised stem asks about multiple issue rather than incorrectly claiming that wider instruction supply necessarily reduces individual memory latency.
Evidence in the complete study note
Superscalar execution issues multiple instructions to multiple functional units in a cycle when dependencies permit.COA36
“Fetch/decode one instruction while executing another” describes pipelining, whereas issuing several instructions in one cycle requires multiple-issue resources.COA35
Choice by choice
A · incorrect — Pipelining overlaps stages but does not by itself require multiple issue.
B · incorrect — Caching retains memory-block copies and is not the multiple-issue technique.
C · correct — Superscalar execution issues multiple instructions to multiple units in a cycle.
D · incorrect — Instruction-level parallelism is the broader property exploited rather than this specific issue mechanism.
Question 100
Which technique translates source or intermediate code into target code during program execution, before the translated portion runs?
A. Pipelining
B. Caching
C. Superscalar architecture
D. Just-in-time (JIT) compilation
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
Correct answer: D — Just-in-time (JIT) compilation
JIT compilation translates code while the program is running, often compiling an intermediate representation before executing that portion. This timing distinguishes it from ahead-of-time translation. Pipelining overlaps processing stages, caching retains copies of data or instructions, and superscalar execution issues multiple instructions to execution resources. Those mechanisms do not name runtime source-to-target compilation.
Evidence in the complete study note
JIT compilation happens during program execution, often translating intermediate code.COA02
Translation before execution alone does not distinguish JIT from an ahead-of-time compiler.COA02
Choice by choice
A · incorrect — Pipelining overlaps stages of executing instructions; it does not translate high-level or intermediate code.
B · incorrect — Caching retains data or instruction copies; it does not perform the compilation described in the stem.
C · incorrect — Superscalar architecture issues multiple instructions; it does not translate a source language into target code.
D · correct — JIT is the only offered compiler; it translates during program execution before the compiled portion executes.
Question 101
Which technique improves performance by predicting the next set of instructions to be
executed based on past execution patterns?
A. Pipelining
B. Caching
C. Superscalar architecture
D. Branch prediction
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Predicting which instruction stream follows a branch is the direction/target prediction described in COA36. Using past patterns is consistent with that prediction role, whereas pipeline overlap, cached memory copies and multiple instruction issue address different mechanisms. Prediction remains speculative: a wrong guess discards work rather than changing the program’s required architectural result.
COA36 describes out-of-order execution as scheduling ready operations before stalled older ones while preserving architectural results and exceptions. This is dynamic reordering to exploit instruction-level parallelism. Superscalar issue can provide execution width but does not itself define such reordering. Pipelining overlaps stages and caching improves reuse; neither names the readiness-based dynamic scheduling mechanism.
Evidence in the complete study note
Out-of-order execution schedules ready operations before stalled older ones while preserving architectural results and exception behavior.COA36
Choice by choice
A · incorrect — Pipelining overlaps stages; dynamic instruction reordering requires an additional readiness-based execution mechanism.
B · incorrect — Caching keeps reusable memory copies and does not itself reorder instruction execution.
C · incorrect — Superscalar issue permits multiple instructions per cycle but does not necessarily require out-of-order scheduling.
D · correct — Out-of-order execution schedules ready instructions around stalled older ones while preserving required results.
Question 103
Which technique improves performance by dynamically allocating processor resources
based on program behavior?
A. Pipelining
B. Caching
C. Superscalar architecture
D. Dynamic resource allocation
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
COA36 explicitly defines dynamic resource allocation as assigning available internal entries/units at runtime. That definition directly fits the stem’s allocation based on behavior during execution. Pipelining describes overlapping stages, caching describes memory reuse, and superscalar execution describes issuing several instructions. They may use allocated resources, but none is the specific allocation technique named by the question.
Evidence in the complete study note
Dynamic resource allocation assigns available internal entries/units at runtime.COA36
Choice by choice
A · incorrect — Pipelining defines overlapping instruction stages rather than the general assignment of runtime internal resources.
B · incorrect — Caching retains memory copies; it does not name the runtime assignment of processor entries and units.
C · incorrect — Superscalar execution names multiple issue, rather than the allocation process used to assign available resources.
D · correct — The note explicitly defines this as assigning available internal processor entries and units at runtime.
Question 104
Which listed item is a fundamental logic building block from which computer hardware is constructed?
A. CPU
B. Memory
C. Hard disk
D. Logic gate
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
Logic gates perform elementary Boolean functions and are fundamental building blocks of digital hardware. A CPU, memory system and hard disk are larger components built from many lower-level mechanisms. The final option identifies the logic-level building block. The question explicitly states the level of abstraction so that basic does not mean an arbitrary major system component.
Evidence in the complete study note
Gates are fundamental logic building blocks; distinguish that level from CPU, memory, disk and motherboard components.COA01
Choice by choice
A · incorrect — A CPU is a major assembled component rather than a fundamental logic building block.
B · incorrect — Memory is a storage component rather than the requested logic-level building block.
C · incorrect — A hard disk is a complex storage device.
D · correct — A logic gate is the fundamental logic-level building block requested.
Question 105
Which component is responsible for executing instructions and performing calculations in a
computer?
A. CPU
B. Memory
C. Hard disk
D. Motherboard
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The CPU contains the control unit, ALU and execution registers. Control sequences operations and transfers, while the ALU performs arithmetic and logic, supporting the CPU’s instruction-processing role. Main memory supplies addressed working storage, a hard disk supplies persistent storage, and the motherboard connects components. Those roles distinguish the processing component from the storage and interconnection choices.
Evidence in the complete study note
The CPU contains an ALU, control unit and registers; a microcontroller is a complete integrated control system, not another mandatory CPU subunit.COA01
The ALU computes; the control unit sequences and enables the transfers.COA11
A motherboard physically connects components.COA01
Choice by choice
A · correct — CPU’s processing/execution function is explicit (pp.6,57).
B · incorrect — Main memory stores data (p.6), rather than being the arithmetic execution unit.
C · incorrect — Disk is secondary storage (p.94), not the processing unit.
D · incorrect — The motherboard physically interconnects components; the CPU carries out the instruction execution and calculations.
Question 106
Which component retains stored data and instructions without power? Here Memory means ordinary volatile main RAM, and CPU excludes separate firmware storage.
A. CPU
B. Memory
C. Hard disk
D. Motherboard
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
An HDD preserves magnetic patterns without continuous power, so the hard disk retains the stored data and instructions. The question now restricts Memory to ordinary volatile main RAM, avoiding the broader meaning that would include ROM or flash. CPU and motherboard name processing and interconnection components rather than the persistent storage mechanism sought. These scope conditions make the intended retention comparison definite.
Evidence in the complete study note
It does not need continuous power to preserve stored bits.COA28
Both are ordinarily volatile.COA24
Ordinary flip-flops and SRAM lose state when power is removed.COA05
Choice by choice
A · incorrect — The CPU is not the specified persistent storage component.
B · incorrect — Ordinary main RAM is volatile under the stated meaning.
C · correct — An HDD retains its stored bits without continuous power.
D · incorrect — The motherboard interconnects components rather than naming the persistent storage mechanism.
Question 107
The motherboard of a computer is responsible for:
A. Executing instructions
B. Storing data
C. Connecting different components
D. Performing calculations
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
Correct answer: C — Connecting different components.
COA01 explicitly states that a motherboard physically connects components. The same section locates the ALU, control unit and registers in the CPU; computation and instruction execution therefore belong to processing components rather than the board’s defining role. Memory provides data storage. The question asks the motherboard’s responsibility, for which physical connection is the specific supported answer.
Evidence in the complete study note
A motherboard physically connects components.COA01
Choice by choice
A · incorrect — Instructions are executed by the CPU; that is distinct from the motherboard’s physical connection role.
B · incorrect — Data storage belongs to memory/storage components, rather than defining what the motherboard itself does.
C · correct — The note explicitly identifies the motherboard as physically connecting the computer’s components.
D · incorrect — Calculations belong to CPU arithmetic/logic hardware rather than the motherboard’s defining connection function.
Question 108
Which component supplies the addressable main working store for a running program, distinct from individual CPU execution registers and persistent disk storage?
A. CPU
B. Main memory (RAM)
C. Hard disk
D. Motherboard
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Main RAM holds the addressed working instructions and data used by a running program. CPU registers hold particular fetched instructions, operands or results for immediate execution, and disks retain information persistently. The motherboard connects these components. Specifying the main working-store role prevents the broad temporary-storage description from also fitting CPU registers or cache.
Evidence in the complete study note
In the textbook Von Neumann model, instructions and data share an addressed memory system; the CPU normally advances sequentially unless control flow changes.COA02
DRAM stores charge and requires refresh: denser and commonly used for main memory.COA24
Registers and cache both store temporary information, but registers are explicit execution operands and cache holds copies of memory blocks.COA14
It does not need continuous power to preserve stored bits.COA28
A motherboard physically connects components.COA01
Choice by choice
A · incorrect — The CPU executes operations and has immediate registers, but is not the main addressed RAM store requested.
B · correct — Main RAM is the addressable working store for the running program’s instructions and data.
C · incorrect — A hard disk supplies persistent storage rather than the main RAM working store.
D · incorrect — The motherboard provides physical component connections rather than this storage role.
Question 109
Which type of software controls and manages the hardware resources of a computer?
A. Operating system
B. Application software
C. Programming language
D. Compiler
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
COA02 directly defines the operating system as managing resources and providing services. Applications solve user tasks, and compilers translate source into target code. A programming language is a means of expressing programs rather than the software resource manager. Therefore the operating system is the single option whose stated role matches controlling and managing computer hardware resources.
Evidence in the complete study note
An operating system manages resources and provides services.COA02
Applications solve user tasks.COA02
A compiler translates source into target code; assembly is a symbolic form of machine instructions.COA02
Choice by choice
A · correct — The operating system is explicitly defined as the resource manager and provider of system services.
B · incorrect — Applications solve user tasks using system services rather than serving as the general hardware resource manager.
C · incorrect — A programming language expresses programs; it is not itself the system software managing hardware resources.
D · incorrect — A compiler translates source code into target code rather than performing general OS resource management.
Question 110
Which software allows users to perform specific tasks or functions on a computer?
A. Operating system
B. Application software
C. Programming language
D. Compiler
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
COA02 states that applications solve user tasks. This directly matches software allowing users to perform particular tasks or functions. The operating system instead manages resources and provides services; a compiler translates programs, and a programming language expresses them. These support applications but do not name the general category of user-task software requested here.
Evidence in the complete study note
An operating system manages resources and provides services.COA02
Applications solve user tasks.COA02
A compiler translates source into target code; assembly is a symbolic form of machine instructions.COA02
Choice by choice
A · incorrect — The OS supplies resource management and services rather than naming the category of specific user-task programs.
B · correct — Applications are explicitly described as software solving user tasks, matching the question’s requested category.
C · incorrect — A programming language is a notation for programs, not the category of software performing user tasks.
D · incorrect — A compiler specifically translates code; application software is the general user-task category requested.
Question 111
Which component provides main working storage for the program’s instructions and data, rather than the CPU’s immediate execution registers or persistent disk storage?
A. CPU
B. Main memory (RAM)
C. Hard disk
D. Motherboard
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Main memory supplies the addressed working storage that holds a program’s instructions and data during operation. CPU registers retain particular fetched instructions, operands and results for immediate execution, while a hard disk supplies persistent storage. The revised stem and expanded memory label distinguish these levels rather than assuming all temporary storage belongs exclusively to one component. A motherboard provides physical interconnection rather than the requested storage role.
Evidence in the complete study note
In the textbook Von Neumann model, instructions and data share an addressed memory system; the CPU normally advances sequentially unless control flow changes.COA02
DRAM stores charge and requires refresh: denser and commonly used for main memory.COA24
Registers and cache both store temporary information, but registers are explicit execution operands and cache holds copies of memory blocks.COA14
It does not need continuous power to preserve stored bits.COA28
Choice by choice
A · incorrect — CPU registers serve immediate execution rather than the main working-storage level requested.
B · correct — Main RAM is the addressed working store for program instructions and data.
C · incorrect — A hard disk provides persistent backing storage rather than main working storage.
D · incorrect — The motherboard physically connects components.
Question 112
Which type of software translates high-level programming languages into machine code?
A. Operating system
B. Application software
C. Programming language
D. Compiler
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
A compiler translates source code into target code; in this question the source is a high-level language and the target is machine code. The operating system manages resources, applications solve user tasks, and a programming language is the notation in which a program is expressed. The requested translation function therefore belongs to the compiler category.
Evidence in the complete study note
An operating system manages resources and provides services.COA02
Applications solve user tasks.COA02
A compiler translates source into target code; assembly is a symbolic form of machine instructions.COA02
Choice by choice
A · incorrect — An operating system manages resources and provides services; compiler is the translation category requested.
B · incorrect — Application software solves user tasks rather than naming the general source-to-target translation category.
C · incorrect — The passage distinguishes source high-level language from resulting machine language; a language itself is not the named translating agent (p.77).
D · correct — Compiler support is explicitly tied to high-level-to-machine translation (p.77).
Question 113
The system clock in a computer is responsible for:
A. Controlling the execution speed of instructions
B. Storing data and instructions
C. Managing the input/output devices
D. Connecting different hardware components
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Correct answer: A — Controlling the execution speed of instructions
Control selections are available at the beginning of a clock cycle and register data are captured on the next clock transition (PDF p.59). Fetch timing likewise advances after each clock pulse (p.55). Thus A is the closest description of clock timing instruction steps; it does not mean frequency alone determines total execution time.
Evidence in the complete study note
Clocked sequential circuits update at designated clock events; combinational logic does not inherently require a clock.COA05
CPU time=instruction_count×CPI×clock_period=instruction_count×CPI/clock_rate.COA34
Choice by choice
A · correct — Clock transitions time the operations and sequence steps (pp.55,59); this regulates execution pace.
B · incorrect — Registers and memory store bits; the clock times their updates rather than stores the program (p.59).
C · incorrect — I/O management is assigned to interfaces/control mechanisms, not solely the clock (pp.101–102).
D · incorrect — Interconnection provides communication (p.6); the clock provides timing rather than that physical connection.
Question 114
Which process is responsible for fetching instructions from memory?
A. Decoding
B. Execution
C. Fetching
D. Storing
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The instruction-pipeline list explicitly begins “Fetch the instruction from memory” (PDF p.117), and the fetch micro-operations copy memory into IR (p.55). The question names this retrieval phase, not interpretation or computation.
Evidence in the complete study note
A conceptual instruction cycle fetches an instruction, decodes opcode/addressing fields, obtains operands, executes, writes results where required and checks permitted interrupts.COA15
A sample fetch is MAR←PC; MDR←M[MAR]; IR←MDR; PC←PC+instruction_length.COA15
Choice by choice
A · incorrect — Decoding interprets the retrieved instruction after fetching (p.117).
B · incorrect — Execution carries out the operation later in the pipeline (p.117).
C · correct — Fetching is the memory-to-instruction-register retrieval phase (pp.55,117).
D · incorrect — Storing writes the result after execution, the opposite transfer purpose (p.117).
Question 115
Which process decodes the fetched instruction and determines the necessary actions?
A. Decoding
B. Execution
C. Fetching
D. Storing
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The module says decoding determines the operation, addressing mode and operand location (PDF p.70). It follows fetch and precedes execution in the instruction phases (p.117).
Evidence in the complete study note
A conceptual instruction cycle fetches an instruction, decodes opcode/addressing fields, obtains operands, executes, writes results where required and checks permitted interrupts.COA15
An opcode specifies the operation; operand fields locate data or registers, and a mode field explains interpretation.COA16
Choice by choice
A · correct — Decoding explicitly determines the required operation and addressing details.
B · incorrect — Execution performs the operation after it has been determined (p.117).
C · incorrect — Fetching retrieves the instruction bits before they are interpreted (p.117).
D · incorrect — Storing writes the computed result, not the operation interpretation (p.117).
Question 116
Which process carries out the actual operations or calculations specified by the instruction?
A. Decoding
B. Execution
C. Fetching
D. Storing
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The instruction stages separate fetch, decode, operand access, execution and result storage (PDF p.117). ALU supplies the required micro-operations for execution (p.57), so actual calculation is execution rather than any transport phase.
Evidence in the complete study note
A conceptual instruction cycle fetches an instruction, decodes opcode/addressing fields, obtains operands, executes, writes results where required and checks permitted interrupts.COA15
The control unit coordinates fetching and data flow; the ALU performs arithmetic and logic.COA15
Choice by choice
A · incorrect — Decoding determines what to do, not the arithmetic itself.
B · correct — Execution is the listed phase that performs the operation (pp.57,117).
C · incorrect — Fetching retrieves the instruction and precedes the calculation (p.117).
D · incorrect — Storing preserves the result after calculation (p.117).
Question 117
Which process is responsible for storing the results of the executed instruction?
A. Decoding
B. Execution
C. Fetching
D. Storing
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The instruction-pipeline sequence ends by storing the result in its proper place (PDF p.117). The RISC variant specifies writing the result into a register (p.118), establishing the result-preservation role of D.
Evidence in the complete study note
A conceptual instruction cycle fetches an instruction, decodes opcode/addressing fields, obtains operands, executes, writes results where required and checks permitted interrupts.COA15
A write-back/result-storage phase is not another fetch.COA15
Choice by choice
A · incorrect — Decoding interprets operation and addressing fields, before a result exists.
B · incorrect — Execution produces a result; the listed store phase preserves it afterward (p.117).
C · incorrect — Fetching brings in the instruction, not its eventual result (p.117).
D · correct — Store result/write register is the explicit final stage (pp.117–118).
Question 118
Which unit of the CPU is responsible for fetching instructions and data from memory?
A. Arithmetic Logic Unit (ALU)
B. Control Unit (CU)
C. Cache Unit
D. Register Unit
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
The pipeline description explicitly says the control unit initiates the next fetch when there is buffer space (PDF p.117). CPU control supervises register transfers and ALU work (p.57); the fetch micro-operations transfer address and instruction bits (p.55). This is coordinating responsibility, not a claim the CU physically stores all fetched data.
Evidence in the complete study note
The control unit coordinates fetching and data flow; the ALU performs arithmetic and logic.COA15
A sample fetch is MAR←PC; MDR←M[MAR]; IR←MDR; PC←PC+instruction_length.COA15
Choice by choice
A · incorrect — ALU performs the arithmetic/logical micro-operations, not the fetch-sequencing role (p.57).
B · correct — CU initiates fetch and supervises the register transfers (pp.57,117).
C · incorrect — Cache supplies stored copies on hits (p.84); it does not decide the instruction-cycle control sequence.
D · incorrect — Registers hold address/data/instruction values, while CU controls their transfers (pp.48,57).
Question 119
Which unit of the CPU performs arithmetic and logical operations?
A. Arithmetic Logic Unit (ALU)
B. Control Unit (CU)
C. Cache Unit
D. Register Unit
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
ALU is explicitly the CPU part that performs required micro-operations; the module classifies arithmetic and logical manipulation as computational operations (PDF pp.57,74–75). Control selects the operation and registers supply/receive values.
Evidence in the complete study note
The ALU computes; the control unit sequences and enables the transfers.COA11
The CPU contains an ALU, control unit and registers; a microcontroller is a complete integrated control system, not another mandatory CPU subunit.COA01
Choice by choice
A · correct — ALU performs required arithmetic/logical micro-operations (p.57).
B · incorrect — CU directs transfers and tells ALU which operation to perform (p.57).
C · incorrect — Cache is a fast storage buffer (p.84), not the computation unit.
D · incorrect — Register set stores intermediate data; ALU operates on it (p.57).
Question 120
Which CPU storage class holds explicit execution operands and results, rather than copies of memory blocks?
A. Arithmetic Logic Unit (ALU)
B. Control Unit (CU)
C. Cache Unit
D. Register Unit
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Registers hold explicit execution operands and results. Cache also stores temporary information, but its role is retaining copies of memory blocks near the processor. The revised question uses that role distinction, so temporary storage alone no longer makes both choices correct. The ALU performs arithmetic and logic, and the control unit coordinates operations rather than being the requested operand-storage class.
Evidence in the complete study note
Registers and cache both store temporary information, but registers are explicit execution operands and cache holds copies of memory blocks.COA14
The accumulator holds operands/results, SP tracks the stack, and status flags report conditions.COA14
Choice by choice
A · incorrect — The ALU computes rather than being the operand-storage class.
B · incorrect — The control unit sequences operations rather than holding explicit execution operands as its defining role.
C · incorrect — Cache holds copies of memory blocks.
D · correct — Registers hold explicit execution operands and results.
Question 121
Which component of the CPU controls the flow of data and instructions within the CPU?
A. Arithmetic Logic Unit (ALU)
B. Control Unit (CU)
C. Cache Unit
D. Register Unit
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
CU explicitly supervises information transfers among registers and tells ALU what operation to perform (PDF p.57). The bus-control example selects sources, operation and destination (p.59), matching control of internal flow.
Evidence in the complete study note
The ALU computes; the control unit sequences and enables the transfers.COA11
A control word chooses ALU sources, destination and operation.COA14
Choice by choice
A · incorrect — ALU processes operands selected by control (pp.57,59), rather than directs the overall flow.
B · correct — CU selects register sources, destination and ALU operation (p.59).
C · incorrect — Cache stores instruction/data copies (p.84), not the CPU transfer-control sequence.
D · incorrect — Registers hold intermediate data; CU controls their transfers (p.57).
Question 122
Which CPU-near storage component retains copies of memory blocks to speed repeated or nearby memory accesses?
A. Arithmetic Logic Unit (ALU)
B. Control Unit (CU)
C. Cache Unit
D. Register Unit
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Cache retains copies of memory blocks near the CPU and exploits temporal and spatial locality. Registers instead hold explicit execution operands and results, even though frequently used values may also remain there. The ALU computes values and the control unit sequences operations. The memory-block-copy criterion therefore identifies cache without claiming that no other CPU component can hold useful data.
A fetch uses the selected PC to obtain an instruction and can advance it to the sequential address. Executing a taken branch can later replace that sequential value with the branch target. The question now specifically asks about that branch action, rather than the broader process of selecting, reading or advancing a next instruction address. Decode interprets fields and write-back stores results; neither is the conceptual branch-execution role requested.
Evidence in the complete study note
A branch can replace the sequential PC later.COA15
A conceptual instruction cycle fetches an instruction, decodes opcode/addressing fields, obtains operands, executes, writes results where required and checks permitted interrupts.COA15
Choice by choice
A · incorrect — Decoding interprets opcode and addressing fields rather than performing the specified branch action.
B · correct — Executing the taken branch replaces the sequential PC with its target.
C · incorrect — Fetching obtains the instruction at the selected address rather than performing this branch action.
D · incorrect — Result storage is not the conceptual branch-target execution phase.
Question 124
What is the purpose of an opcode in a 16-bit instruction format (4-bit opcode | 6-bit operand ref
| 6-bit operand ref)?
A. It holds the destination address of an operand
B. It determines the operation to be done
C. It holds the source address of an operand
D. It holds the next instruction reference
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: B — It determines the operation to be done
The stated field widths sum to 16 bits: 4+6+6. Their widths do not change the opcode’s purpose: operation selection (PDF p.47). Operand reference fields identify source/destination values or locations; PC tracks sequence.
Evidence in the complete study note
An opcode specifies the operation; operand fields locate data or registers, and a mode field explains interpretation.COA16
A 4-bit opcode permits at most 16 encodings, not necessarily 16 implemented instructions.COA16
A 6-bit operand-reference field has 64 encodings; what they designate depends on the machine.COA16
Choice by choice
A · incorrect — Destination reference is an operand/address field, not the opcode (p.47).
B · correct — Operation selection is the explicit opcode definition (p.47).
C · incorrect — Source reference belongs to the operand/address fields (p.47).
D · incorrect — Next instruction is tracked by PC (p.70), not the opcode.
Question 125
Which performance metric can be used to measure the time taken to perform a read or write
operation?
A. Transfer rate
B. Memory cycle time
C. Fetching time
D. Access time
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Access time is the elapsed time from initiation to completion of a memory operation (PDF p.83). Memory cycle time is the minimum separation of successive operations. This distinguishes one read/write duration from transfer throughput or instruction fetching.
Evidence in the complete study note
Access time measures latency of a read/write; cycle time is the minimum interval before another operation and may include recovery.COA23
Transfer rate measures data per time, not individual-request delay.COA23
Choice by choice
A · incorrect — Transfer rate measures an amount per unit time; it is not the single-operation interval defined on p.83.
B · incorrect — Cycle time measures spacing of successive operations, not the requested initiation-to-completion duration (p.83).
C · incorrect — Fetching is one instruction-cycle task, not the general read/write performance metric (p.55).
D · correct — Access time is exactly the operation-duration definition (p.83).
Question 126
Under the textbook access-method taxonomy, how is magnetic-disk block access classified when requests identify blocks but mechanical positioning introduces delay?
A. Associative
B. Sequential
C. Random
D. Direct
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
The stated textbook taxonomy calls magnetic disk access direct: a request identifies an addressed block, but positioning creates access delay. RAM is classified as random access with broadly address-independent timing, while tape is sequential and associative access matches content. Informal usage may call disks random-access devices too, but the revised question explicitly chooses the textbook classification convention rather than treating the labels as universally exclusive.
Evidence in the complete study note
In textbook access taxonomy, tape is sequential, disk is direct access with positioning delay, RAM is random access with broadly address-independent timing, and associative access matches content.COA28
“Random-access disk” is also common informal usage; specify the taxonomy when comparing direct and random access.COA28
Choice by choice
A · incorrect — Associative access matches by content rather than addressed disk blocks.
B · incorrect — Tape-like sequential access is not the disk’s required access pattern.
C · incorrect — Random is the RAM category in the explicitly stated textbook taxonomy.
D · correct — Direct is the disk category in that taxonomy.
Question 127
Which statement reverses the broad integration trend described for computer evolution?
A. Increasing component size
B. Increasing processor speed
C. Increasing integration density
D. Increasing memory size
Hint / Module Reference (Where to Read)
Use the stated historical convention or integration trend, rather than assuming every model has identical characteristics.
The note describes a broad trend toward smaller individual components while density, capacity and processor performance increase. Increasing component size reverses that stated trend. The other alternatives describe growth in performance, integration density or memory capacity and are therefore consistent with it. These are historical tendencies, not guarantees that every later product improves every measured property.
Evidence in the complete study note
Integration generally reduced individual component dimensions while capacity, density and processor performance grew; these are trends rather than guarantees for every model.COA38
Choice by choice
A · correct — The broad trend reduces individual component dimensions, so increasing size reverses it.
B · incorrect — Rising processor performance is consistent with the stated evolutionary tendency.
C · incorrect — Increasing integration density is explicitly part of the stated integration trend.
D · incorrect — Growing storage capacity is consistent with the stated trend even as individual component dimensions shrink.
Question 128
Which one of the following is NOT correct about Von Neumann's architecture?
A. Data and instructions are stored separately
B. Modern computers are based on Von Neumann's architecture
C. Instruction execution is sequential
D. Memory content is located by its address
Hint / Module Reference (Where to Read)
Identify the role requested and compare it with the definitions and constraints in the cited passages.
Correct answer: A — Separate instruction and data storage contradicts the textbook Von Neumann model.
COA02 defines the textbook Von Neumann model as sharing an addressed memory system between instructions and data, with normally sequential execution unless control flow changes. Thus separate storage is the defining contradiction. The note allows modern machines to retain a unified address-space view while using split caches; ordinary execution and addressed memory remain compatible with that model.
Evidence in the complete study note
In the textbook Von Neumann model, instructions and data share an addressed memory system; the CPU normally advances sequentially unless control flow changes.COA02
Harvard separates instruction and data memories or paths.COA02
Choice by choice
A · correct — Separate instruction/data memories describe Harvard organization rather than the textbook shared-memory Von Neumann model.
B · incorrect — Modern systems can retain a unified address-space view, so this broad conventional association is compatible with the note.
C · incorrect — Normally sequential instruction progression is part of the textbook model, with branches providing explicit control-flow changes.
D · incorrect — The model explicitly uses addressed memory, so locating content by address is a compatible statement.
Question 129
Which instruction type is used to test the value of a data word or status of a condition?
A. Data processing instruction
B. Test instruction
C. Data movement instruction
D. Branch instruction
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
COA19 states that TEST/CMP examine values and set condition information, often without retaining an arithmetic result. That exactly matches examining a data word or a condition status. Arithmetic/data processing is a broader computing class, data movement copies values, and branches choose control-flow targets. The named test-instruction category is therefore the direct answer among the options.
Evidence in the complete study note
TEST/CMP examine values and set condition information, often without retaining the arithmetic result.COA19
Branch instructions choose a target, conditionally or unconditionally.COA19
CALL saves a return point; RETURN restores it.COA19
Choice by choice
A · incorrect — Data processing is a broader computing category; the stem specifically requests the instruction used to test values.
B · correct — TEST/CMP examine values and establish condition information, directly matching the question’s described operation.
C · incorrect — Data movement copies values between locations rather than testing their contents or condition status.
D · incorrect — Branches choose control-flow targets, often using previously established conditions rather than performing the requested test.
Question 130
What is the purpose of an opcode in a 16-bit instruction format (4-bit opcode | 6-bit operand ref
6-bit operand ref)?
A. It holds the destination address of an operand
B. It determines the operation to be done
C. It holds the source address of an operand
D. It holds the next instruction reference
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: B — The opcode specifies the operation.
COA16 defines the opcode as specifying the operation and operand fields as locating data/registers. In the given 16-bit format, the 4-bit opcode therefore selects an operation, while the two 6-bit references identify operands under the machine’s interpretation. The bit widths are not evidence that the opcode stores a source/destination address or next-PC reference.
Evidence in the complete study note
An opcode specifies the operation; operand fields locate data or registers, and a mode field explains interpretation.COA16
Choice by choice
A · incorrect — A destination operand reference belongs in an operand field, not in the operation-selecting opcode.
B · correct — The opcode determines which operation the processor should perform for this instruction.
C · incorrect — A source operand reference is an operand-field role rather than the opcode’s operation role.
D · incorrect — The next-instruction reference is a control-flow/PC concern, not the general purpose of this opcode field.
Question 131
A designer adds a PCI expansion card to a processor whose local bus uses a different transfer protocol. The two sides cannot be wired together directly. Which listed hardware category is needed to adapt transfers between the processor bus and the expansion interconnect?
A. SCSI
B. PCI
C. Bus bridge/controller logic
D. Multi bus
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
The scenario requires hardware that adapts transfers between unlike bus segments, so bus bridge/controller logic is needed. PCI identifies the expansion interconnect on one side of the connection; merely naming it does not supply the adaptation to the processor bus. SCSI identifies a storage connection and Multibus another bus family. The distinction is between the interconnect being attached and the hardware that enables the attachment.
Evidence in the complete study note
PCI is a peripheral expansion interconnect, not a disk protocol; connecting unlike bus segments requires suitable bridge/controller logic.COA32
Choice by choice
A · incorrect — SCSI is a storage connection rather than the adapter between these unlike bus segments.
B · incorrect — PCI names the expansion interconnect already present in the scenario, not the adapting component.
C · correct — Bus bridge/controller logic adapts transfers between the unlike processor and expansion bus segments.
D · incorrect — Multibus names a bus family rather than the component needed to adapt this connection.
Question 132
Combinational circuit differ from sequential circuit primarily because
A. Combinational circuit cannot be built using logic circuit
B. The output of combinational circuit depends only on the present input, not on past
output.
C. Sequential circuit have no feedback while combinational circuit do
D. The combinational circuit requires clock signal, but sequential circuit do not
Hint / Module Reference (Where to Read)
Check whether output depends only on current inputs or also on stored state, and track the stated clock behavior.
Correct answer: B — Combinational output depends on present inputs rather than stored history.
COA05 defines combinational output through present inputs after propagation delay, while sequential output also depends on stored state. B expresses that distinction. Combinational circuits are built from logic, not prohibited from it; the feedback statement reverses the usual state relationship. Nor do combinational circuits inherently require a clock, while clocked sequential circuits update at clock events.
Evidence in the complete study note
A combinational output depends on present inputs after propagation delay.COA05
A sequential circuit depends on stored state as well as inputs; registers, counters and flip-flops are examples.COA05
Choice by choice
A · incorrect — Combinational circuits are logic circuits; the statement incorrectly denies their ordinary implementation basis.
B · correct — Present inputs determine combinational outputs, whereas sequential circuits additionally depend on retained state.
C · incorrect — This reverses the state/feedback distinction; sequential storage can involve feedback, not its categorical absence.
D · incorrect — Combinational logic does not inherently require a clock; clock events characterize clocked sequential updates.
Question 133
Which one of the following is the first operation or step in CPU instruction cycle?
A. Executing the instruction
B. Handling interrupt
C. Decoding the instruction
D. Fetching the instruction
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
COA15 begins the conceptual instruction cycle with fetch, then decode, operand acquisition, execution and any result write-back. Fetch must obtain the instruction before its opcode can be decoded and operation performed. Permitted interrupt checks are a separate stage/transition in that conceptual model, not the first ordinary instruction-processing step among these choices.
Evidence in the complete study note
A conceptual instruction cycle fetches an instruction, decodes opcode/addressing fields, obtains operands, executes, writes results where required and checks permitted interrupts.COA15
Choice by choice
A · incorrect — Execution follows obtaining and decoding the instruction, rather than being the cycle’s first conceptual step.
B · incorrect — Interrupt checks/service are distinct from the first ordinary fetch step in the note’s conceptual cycle.
C · incorrect — Decoding requires an already fetched instruction, so it follows rather than precedes fetch.
D · correct — Fetching obtains the instruction and is explicitly first in the conceptual instruction-cycle sequence.
Question 134
____________ is a data transfer method in computer organization and architecture that
allows an I/O device to transfer data directly to or from memory without the involvement
of the CPU.
A. Asynchronous data transfer
B. Direct Memory Access (DMA)
C. Interrupt-driven transfer
D. Programmed I/O transfer
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
COA30 says DMA lets a controller transfer a block directly between device and memory after CPU setup. The stem’s without CPU involvement must mean without CPU moving every item, not no configuration/completion involvement whatsoever. Polling and interrupt-driven I/O still require CPU transfer work; asynchronous transfer describes timing coordination rather than this block-moving mechanism.
Evidence in the complete study note
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
Choice by choice
A · incorrect — Asynchronous transfer describes coordination/timing rather than specifically controller-managed movement directly between device and memory.
B · correct — DMA transfers the block through a controller after CPU setup, avoiding per-item CPU copying.
C · incorrect — Interrupt-driven handlers still consume CPU time to service and move device data in this comparison.
D · incorrect — Programmed I/O repeatedly checks status and has the CPU move each item rather than using DMA.
Question 135
Which logic gate produces output 1 only when ALL inputs are 1?
A. OR gate
B. AND gate
C. NAND gate
D. XOR gate
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
COA03 states that AND is 1 only when all inputs are 1. This is exactly the condition in the stem. OR needs any high input, NAND complements AND, and two-input XOR is high when inputs differ. Thus none of the other truth functions has the specified all-high-only output rule.
Evidence in the complete study note
AND is 1 only when all inputs are 1; OR is 1 if any input is 1.COA03
Choice by choice
A · incorrect — OR becomes high when any input is high, so it does not require all inputs to be one.
B · correct — AND outputs one exactly for the all-inputs-one combination required by the stem.
C · incorrect — NAND inverts AND and therefore outputs zero, not one, when all its inputs are one.
D · incorrect — Two-input XOR outputs one when inputs differ, not when both inputs are one.
Question 136
The Boolean expression F = A⊕B represents which gate?
A. XNOR gate
B. NOR gate
C. XOR gate
D. NAND gate
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
The expression A⊕B is the exclusive-OR operation. COA03 defines its two-input output as 1 when the inputs differ and contrasts XNOR as agreement. NOR and NAND complement OR and AND instead. Thus XOR is the operation represented by the given symbol, with no extra circuit diagram or numeric assumption needed.
Evidence in the complete study note
The circled plus symbol ⊕ denotes exclusive OR.COA-S06
NAND complements AND; NOR complements OR.COA03
For two inputs XOR is 1 when inputs differ, and XNOR when they agree.COA03
Choice by choice
A · incorrect — XNOR is the complement of XOR, giving one when the two inputs agree.
B · incorrect — NOR complements OR; it is not the exclusive-OR operation denoted by the circled plus.
C · correct — The circled-plus expression denotes exclusive OR, whose output is one for differing inputs.
D · incorrect — NAND complements AND rather than implementing the given exclusive-OR expression.
Question 137
Which gate is called the 'universal gate' because it can implement any Boolean function?
A. AND gate
B. OR gate
C. NAND gate
D. XOR gate
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
Correct answer: C — NAND, the only universal gate offered.
COA04 explicitly states that NAND and NOR are each universal and explains constructing NOT by tying inputs together, then building AND/OR combinations. Of those two universal families, only NAND is offered. AND and OR alone cannot provide inversion under this rule, and XOR is not identified as a universal family. Thus the correct offered gate is NAND.
Evidence in the complete study note
NAND and NOR are each universal: feeding the same input to both inputs constructs NOT; combine complemented gates to construct AND or OR.COA04
Choice by choice
A · incorrect — AND alone is not the universal family described; it does not supply the required inversion construction.
B · incorrect — OR alone is not the universal family described and cannot generate the stated NOT construction.
C · correct — NAND is explicitly universal and can be combined to construct NOT, AND and OR.
D · incorrect — XOR is not the NAND/NOR universal family; tied inputs produce zero rather than inversion.
Question 138
For a NOR gate with inputs A=1, B=0, the output F is:
A. 0
B. 1
C. Undefined
D. Depends on voltage
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
COA03 defines OR as high when any input is high and NOR as its complement. At A=1, B=0, the OR value is 1, so NOR produces 0. The input combination is completely specified in ordinary Boolean logic; it is neither undefined nor dependent on an unspecified analog voltage model.
Evidence in the complete study note
AND is 1 only when all inputs are 1; OR is 1 if any input is 1.COA03
NAND complements AND; NOR complements OR.COA03
Choice by choice
A · correct — OR of 1 and 0 is 1; complementing that for NOR yields zero.
B · incorrect — One is the OR result before inversion, not the NOR output for these inputs.
C · incorrect — The Boolean NOR truth table fully defines this ordinary input combination.
D · incorrect — The stem supplies Boolean input values, so no additional voltage threshold assumption is required.
Question 139
De Morgan's theorem states that NOT(A·B) equals:
A. NOT(A) · NOT(B)
B. NOT(A) + NOT(B)
C. A + B
D. NOT(A+B)
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
COA04 gives (AB)'=A'+B'. Complementing a product changes AND to OR and complements each operand. B matches that exact transformation. A instead gives the complement of A+B, C omits the operand complements, and D leaves the complement attached to a sum, which represents NOR rather than the requested NAND function.
Evidence in the complete study note
De Morgan gives (AB)'=A'+B' and (A+B)'=A'B'.COA04
Choice by choice
A · incorrect — The product of complements equals NOT(A+B), rather than the complement of the original product.
B · correct — Complement each operand and change AND to OR, exactly as De Morgan’s product rule states.
C · incorrect — A+B omits both required complements and is not generally equal to NOT(A·B).
D · incorrect — NOT(A+B) is NOR and differs from NOT(A·B), for example when only one input is high.
Question 140
In Boolean algebra, the expression A + A' (A OR NOT A) always equals:
A. 0
B. A
C. 1
D. A'
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
COA04 explicitly lists A+A'=1. If A is 0 then A' is 1, and if A is 1 then A' is 0; either way their Boolean OR is 1. Neither A nor A' remains fixed across both assignments, and zero is the product-of-complements result rather than their sum.
Evidence in the complete study note
Useful identities are A+0=A, A·1=A, A+A=A, AA=A, A+A'=1, AA'=0, A+AB=A and A(A+B)=A.COA04
Choice by choice
A · incorrect — Zero is A AND NOT A; the given operation is OR, so one input is always high.
B · incorrect — A can be zero while the expression remains one, so the identity is not simply A.
C · correct — A bit OR its complement is always one for both possible assignments.
D · incorrect — A complement can be zero while the full expression is one, so it is not the constant result.
Question 141
How many rows are in the truth table for a Boolean function with 4 input variables?
A. 8
B. 12
C. 16
D. 32
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
COA03 gives 2^n rows for n binary inputs. For four independent variables, each has two assignments, so the total combinations are 2×2×2×2=16. The options 8 and 32 correspond to three and five binary variables respectively; 12 does not enumerate all four-variable combinations.
Evidence in the complete study note
With n binary inputs, enumerate 2^n truth-table rows.COA03
Choice by choice
A · incorrect — Eight is 2^3, the number of assignments for three inputs rather than four.
B · incorrect — Twelve omits four of the sixteen possible combinations of four independent binary inputs.
C · correct — Four independent binary inputs yield 2^4=16 distinct truth-table rows.
D · incorrect — Thirty-two is 2^5 and would require five independent binary input variables.
Question 142
For the Boolean function F=x+y'z with x=0,y=1,z=1, which options evaluate to the same Boolean value as F under that assignment? Select all that apply.
A. 0
B. 1
C. x
D. z
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
Complement first: y is one, so y-prime is zero. The product y-prime AND z is therefore zero, and OR with x, also zero, leaves F equal to zero. Both the literal zero option and the expression x evaluate to that result under the stated assignment. The literal one and z both evaluate to one. The multiple-selection wording preserves the actual option values rather than arbitrarily rejecting an equivalent expression.
Evidence in the complete study note
Evaluate complements, products and then sums.COA03
A plus sign means Boolean OR, not integer addition.COA03
Useful identities are A+0=A, A·1=A, A+A=A, AA=A, A+A'=1, AA'=0, A+AB=A and A(A+B)=A.COA04
Choice by choice
A · correct — The literal zero equals the computed function value.
B · incorrect — One differs from the computed zero.
C · correct — x is assigned zero and therefore equals the function value.
D · incorrect — z is assigned one and differs from the function value.
Question 143
Which characteristic best describes a flip-flop?
A. A combinational logic circuit
B. A bistable multivibrator that stores one bit
C. A 4-bit counter
D. An arithmetic unit
Hint / Module Reference (Where to Read)
Check whether output depends only on current inputs or also on stored state, and track the stated clock behavior.
Correct answer: B — A bistable one-bit storage element.
COA05 says a flip-flop stores one bit while powered and classifies flip-flops as sequential circuits with stored state. B is the option describing that storage element. A combinational circuit lacks stored logical state; a four-bit counter requires a multi-bit state structure, and an arithmetic unit computes rather than defining this one-bit storage component.
Evidence in the complete study note
A flip-flop is bistable: it has two stable states representing 0 and 1.COA-S07
Multiple flip-flops are required to represent a multi-bit counter state.COA-S07
A combinational output depends on present inputs after propagation delay.COA05
Choice by choice
A · incorrect — A combinational circuit has no stored logical state, whereas a flip-flop retains a bit.
B · correct — Bistable one-bit storage matches the powered state-retention role of a flip-flop.
C · incorrect — One flip-flop stores one bit; a four-bit counter requires a multi-bit state organization.
D · incorrect — An arithmetic unit computes values rather than defining the one-bit sequential storage element.
Question 144
What distinguishes a flip-flop from a simple logic gate in terms of memory?
A. Flip-flops use more power
B. Flip-flops retain state even after inputs change
C. Flip-flops operate faster
D. Flip-flops require AC power
Hint / Module Reference (Where to Read)
Check whether output depends only on current inputs or also on stored state, and track the stated clock behavior.
Correct answer: B — Flip-flops retain stored state during powered operation.
COA05 distinguishes sequential state from combinational outputs determined by present inputs. A flip-flop can retain its bit when inputs change without a qualifying update, giving the memory distinction in B. This does not imply nonvolatile retention after power-off. Power, speed and AC-supply claims are neither the defining property nor guarantees established here.
Evidence in the complete study note
A flip-flop stores one bit while powered.COA05
State retention during operation does not mean nonvolatile storage.COA05
Choice by choice
A · incorrect — Power consumption is implementation-dependent and does not define whether a circuit has logical memory.
B · correct — Stored state persists between valid updates while powered, unlike a purely present-input combinational gate.
C · incorrect — Speed is not the defining memory distinction and is not guaranteed by the flip-flop label.
D · incorrect — The note specifies powered storage, not a requirement for an AC rather than another supply.
Question 145
What is the decimal equivalent of binary number 1011?
A. 9
B. 10
C. 11
D. 13
Hint / Module Reference (Where to Read)
Keep the radix, bit width and representation fixed; evaluate place values or arithmetic steps in order.
Using COA08’s base-position rule, 1011₂ has weights 8, 4, 2 and 1. Its high bits contribute 8+2+1=11, while the 4-place is zero. The note’s worked example confirms the same sum. Nine, ten and thirteen correspond to different low-order bit patterns, not the supplied 1011.
Evidence in the complete study note
In base b, a digit at position i has value digit×b^i.COA08
Binary uses 0–1, octal 0–7 and hexadecimal 0–9,A–F; F=15.COA08
Choice by choice
A · incorrect — Nine equals 8+1, corresponding to 1001₂ and omitting the given two-place bit.
B · incorrect — Ten equals 8+2, corresponding to 1010₂ and omitting the given one-place bit.
C · correct — The set bit positions contribute 8+2+1=11 in decimal.
D · incorrect — Thirteen equals 8+4+1, corresponding to 1101₂ rather than the supplied 1011₂.
Question 146
In hexadecimal, what does the letter 'F' represent in decimal?
A. 14
B. 15
C. 16
D. 10
Hint / Module Reference (Where to Read)
Keep the radix, bit width and representation fixed; evaluate place values or arithmetic steps in order.
COA08 defines hexadecimal digits as 0–9,A–F and explicitly gives F=15. These sixteen symbols represent values zero through fifteen, so sixteen itself requires the two-digit hexadecimal representation 10. Fourteen is E, and ten is A, leaving fifteen as the only value of the single digit F.
Evidence in the complete study note
Binary uses 0–1, octal 0–7 and hexadecimal 0–9,A–F; F=15.COA08
Choice by choice
A · incorrect — Fourteen corresponds to the preceding hexadecimal digit E, not the final digit F.
B · correct — The note explicitly assigns decimal value fifteen to the hexadecimal digit F.
C · incorrect — Sixteen requires hexadecimal 10; it is outside the value range of a single hexadecimal digit.
D · incorrect — Ten corresponds to hexadecimal A rather than the later digit F.
Question 147
The octal number system uses a base of:
A. 2
B. 8
C. 10
D. 16
Hint / Module Reference (Where to Read)
Keep the radix, bit width and representation fixed; evaluate place values or arithmetic steps in order.
COA08 gives octal digits 0–7: eight possible digit values, so octal has base eight. Binary has two digits, decimal ten and hexadecimal sixteen. Place weights in octal are therefore powers of eight, not powers of two, ten or sixteen, even though octal digits can be grouped with three binary bits.
Evidence in the complete study note
In base b, a digit at position i has value digit×b^i.COA08
Binary uses 0–1, octal 0–7 and hexadecimal 0–9,A–F; F=15.COA08
Choice by choice
A · incorrect — Base two is binary; octal allows eight digit values rather than only zero and one.
B · correct — Octal uses digits zero through seven, giving a base of eight.
C · incorrect — Base ten is decimal, not the eight-digit octal number system.
D · incorrect — Base sixteen is hexadecimal, which uses the additional A–F digits absent from octal.
Question 148
Which number system is most fundamental to digital computing and why?
A. Decimal, because humans use it
B. Octal, because it maps to 3 bits
C. Binary, because digital circuits have two states (on/off)
D. Hexadecimal, because it is compact
Hint / Module Reference (Where to Read)
Apply the gate truth rules and Boolean identities in the stated input order; distinguish an inversion from the underlying operation.
Correct answer: C — Binary matches the two logical states used by digital logic.
COA03 defines digital gates using the two Boolean values 0 and 1, and COA08 defines binary using exactly those two digits. That direct correspondence explains why binary is fundamental to the digital representation described here. Octal and hexadecimal group binary bits for convenience, while decimal’s human familiarity does not supply the two-state circuit correspondence.
Evidence in the complete study note
Binary uses 0–1, octal 0–7 and hexadecimal 0–9,A–F; F=15.COA08
NOT complements a bit.COA03
Choice by choice
A · incorrect — Human decimal familiarity does not match the two Boolean states used here’s digital gates.
B · incorrect — Octal groups three binary bits and is a convenient notation rather than the underlying two-state representation.
C · correct — Binary digits zero and one directly correspond to the two logical values used by digital circuits.
D · incorrect — Hexadecimal compactly groups four binary bits; compact notation does not replace the underlying binary states.
Question 149
How many bits are needed to represent the hexadecimal digit F?
A. 2
B. 3
C. 4
D. 8
Hint / Module Reference (Where to Read)
Keep the radix, bit width and representation fixed; evaluate place values or arithmetic steps in order.
COA08 groups four binary bits for each hexadecimal digit and gives F=15. COA09’s unsigned range shows three bits reach only 7, while four bits reach 15. Therefore the minimum representation of F is four bits, 1111. Eight bits can contain the value but are not the number needed for one hexadecimal digit.
Evidence in the complete study note
Group binary bits in threes for octal and fours for hexadecimal, outward from the radix point.COA08
Binary uses 0–1, octal 0–7 and hexadecimal 0–9,A–F; F=15.COA08
For n-bit unsigned values the range is 0 through 2^n−1.COA09
Choice by choice
A · incorrect — Two bits encode only zero through three, insufficient for hexadecimal F’s decimal value fifteen.
B · incorrect — Three bits encode only zero through seven, so they cannot represent the value fifteen.
C · correct — Four bits encode zero through fifteen; F is represented by the four-bit pattern 1111.
D · incorrect — Eight bits could contain fifteen but exceed the minimum four bits needed for a hexadecimal digit.
Question 150
Which listed memory categories lose their contents when power is removed? Assume ordinary SRAM/DRAM RAM and an SRAM-based processor cache. Select all that apply.
A. ROM
B. Flash memory
C. RAM
D. Cache
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Ordinary SRAM and DRAM require power to retain their contents. RAM therefore qualifies, and the stated SRAM-based cache qualifies for the same technological reason. Cache is a hierarchy role rather than a promise of nonvolatile storage. ROM and flash retain contents without power, so they are excluded. Specifying implementation makes the volatility judgment definite while keeping both valid categories rather than forcing a RAM-only answer.
Evidence in the complete study note
SRAM uses powered bistable storage: fast and costly per bit, without periodic refresh.COA24
DRAM stores charge and requires refresh: denser and commonly used for main memory.COA24
Both are ordinarily volatile.COA24
ROM and flash retain contents without power; erasable/programmed variants mean “ROM can never be modified” is too broad.COA24
Choice by choice
A · incorrect — ROM retains contents without power.
B · incorrect — Flash retains contents without power.
C · correct — Ordinary SRAM/DRAM RAM is volatile.
D · correct — The explicitly SRAM-based cache is volatile too.
Question 151
Cache memory is best described as:
A. Large, slow, cheap memory
B. Small, ultra-fast memory between CPU and RAM
C. Non-volatile backup storage
D. Virtual memory on disk
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: B — Small, fast storage near the CPU between it and main memory.
COA23 places cache above DRAM in the usual speed/cost hierarchy and says faster levels are generally smaller and more expensive per bit. It defines cache as copied memory blocks near the CPU. B captures that role. Cache is not the large slow backup layer or disk-based virtual-memory backing store; its useful speed derives from proximity/reuse, not guaranteed persistence.
Evidence in the complete study note
A usual speed/cost-per-bit order is registers, L1/L2/L3 cache, DRAM, SSD, HDD and archival tape.COA23
Faster levels are generally smaller and more expensive per bit.COA23
Cache copies memory blocks near the CPU.COA23
Choice by choice
A · incorrect — Large slow cheap storage describes lower hierarchy levels rather than the small fast cache layer.
B · correct — Cache is a small fast near-CPU copy of memory blocks used to accelerate access.
C · incorrect — The note defines cache for accelerated reuse, not as nonvolatile backup storage.
D · incorrect — Disk-backed virtual memory is a different address-space/backing-store mechanism from the CPU cache.
Question 152
In direct memory mapping, what happens when two different main memory blocks map to the same cache slot?
A. Both are stored simultaneously
B. A cache conflict occurs and one block replaces the other
C. The system crashes
D. The blocks merge
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: B — A placement conflict: only one block can occupy that direct-mapped slot.
COA25 states that two blocks with the same direct-mapped index cannot reside together. When the requested block differs from the valid block at that slot, the cache must replace the slot’s contents, producing a conflict miss. This is ordinary cache operation, not a crash or merging of block contents; direct mapping offers no alternate placement for the same index.
Evidence in the complete study note
Direct mapping uses line=block mod L.COA25
Two blocks with the same direct-mapped index cannot reside together.COA25
Choice by choice
A · incorrect — One direct-mapped line holds one block at a time, so the colliding blocks cannot coexist there.
B · correct — The shared index causes a placement conflict; installing the requested block replaces the current one.
C · incorrect — Conflict replacement is ordinary cache behavior and does not imply a system crash.
D · incorrect — Cache replacement preserves separate memory-block identities; it does not merge their contents into one block.
Question 153
Which cache mapping technique offers the most flexibility in placing data blocks?
A. Direct mapping
B. Set associative mapping
C. Fully associative mapping
D. Sequential mapping
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
COA25 says direct mapping fixes one line, set associativity permits any way within one indexed set, and fully associative placement permits any line. Allowing every line gives the most placement flexibility for a fixed cache. The sequential-mapping option is not one of the cache placement rules defined by the supplied note.
Evidence in the complete study note
Direct mapping uses line=block mod L.COA25
Fully associative placement permits any line.COA25
A W-way set-associative cache has S=L/W sets and set=block mod S; any of W ways in that set may hold the block.COA25
Choice by choice
A · incorrect — Direct mapping restricts a block to a single line and therefore has the least placement freedom.
B · incorrect — Set associativity permits several ways in one set, fewer locations than the entire fully associative cache.
C · correct — Fully associative placement allows any cache line, maximizing placement freedom for each block.
D · incorrect — Sequential ordering is not a placement freedom comparable to the defined direct, set-associative and fully associative cache rules.
Question 154
Set associative mapping is described as a compromise between:
A. RAM and ROM
B. Direct and fully associative mapping
C. Primary and secondary memory
D. Cache and virtual memory
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: B — Direct and fully associative mapping.
COA25 defines W-way set associativity as fixing a set by the block index while allowing any of W ways inside it. That combines direct indexing with an associative choice within the selected set, placing it between one-line direct mapping and unrestricted fully associative placement. RAM/ROM and primary/secondary are technology/hierarchy contrasts, not the two placement endpoints.
Evidence in the complete study note
Direct mapping uses line=block mod L.COA25
Fully associative placement permits any line.COA25
A W-way set-associative cache has S=L/W sets and set=block mod S; any of W ways in that set may hold the block.COA25
Choice by choice
A · incorrect — RAM and ROM describe memory types rather than the placement-policy endpoints combined by set associativity.
B · correct — Set indexing restricts placement like direct mapping while allowing an associative choice among the selected set’s ways.
C · incorrect — Primary and secondary describe hierarchy roles, not the direct versus associative cache-placement alternatives.
D · incorrect — Cache and virtual memory are different mechanisms rather than the two placement extremes defining set associativity.
Question 155
Virtual memory primarily uses which storage device to extend the apparent memory size?
A. ROM
B. Cache
C. Hard disk / SSD
D. Registers
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: C — Hard disk / SSD as backing storage.
COA27 says backing storage can hold nonresident pages while virtual memory provides translated protected address spaces. COA28 identifies HDDs and SSDs as persistent storage devices, matching that backing role. ROM, cache and registers are not the nonresident-page backing tier described. Apparent extension does not mean physical RAM is added or that virtual memory is only disk disguised as RAM.
Evidence in the complete study note
Virtual memory gives processes translated address spaces and protection; backing storage can hold nonresident pages.COA27
An HDD stores magnetic patterns on tracks divided into sectors; reads/writes access addressed blocks while platters rotate.COA28
SSDs use nonvolatile semiconductor storage without mechanical seek.COA28
Choice by choice
A · incorrect — ROM stores persistent firmware/data but is not the writable nonresident-page backing role described here.
B · incorrect — Cache holds near-CPU copies of memory blocks rather than serving as the mass backing store.
C · correct — Persistent HDD/SSD storage can hold nonresident page contents for the virtual-memory system.
D · incorrect — Registers hold immediate execution state and cannot serve as the large backing store for nonresident pages.
Question 156
A valid disk-backed virtual page is currently nonresident, and the access must load its saved contents before continuing. Which condition describes the resulting page-fault case?
A. The CPU runs out of registers
B. The requested page is not in physical memory and must be loaded from disk
C. Cache memory is full
D. An arithmetic overflow occurs
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: B — The requested page is not in physical memory and must be loaded from disk
Accessing the valid but nonresident disk-backed page faults so that the system can make the page resident and continue. The stated case requires loading its saved contents. Register pressure, cache replacement and arithmetic overflow are different conditions. Other kinds of page fault need not read a disk, so the question explicitly limits itself to this nonresident disk-backed case.
Evidence in the complete study note
A valid nonresident page access faults and may require loading data; invalid or forbidden accesses can also fault.COA27
A cache miss, TLB miss and page fault are different events; not every page fault reads a disk, since zero-fill and already-resident shared pages exist.COA27
Choice by choice
A · incorrect — Register allocation pressure is not an access to a missing or forbidden virtual page.
B · correct — The described disk-backed nonresident access is a page-fault case, although not all faults require a disk read.
C · incorrect — A full cache leads to cache replacement, not necessarily a virtual-memory page fault.
D · incorrect — Arithmetic overflow is an instruction arithmetic condition rather than a virtual-page access event.
Question 157
Compared to RAM, a Hard Disk Drive (HDD) is:
A. Faster and volatile
B. Slower and non-volatile
C. Faster and non-volatile
D. Slower and volatile
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
Correct answer: B — HDD is generally slower and nonvolatile.
COA23 places DRAM above HDD in the usual speed hierarchy. COA28 says an HDD does not require continuous power to preserve stored bits, while COA24 calls ordinary SRAM/DRAM volatile. Combining the independent speed and retention rules gives slower and nonvolatile. The answer concerns the usual hierarchy comparison rather than every conceivable workload or specialized memory device.
Evidence in the complete study note
A usual speed/cost-per-bit order is registers, L1/L2/L3 cache, DRAM, SSD, HDD and archival tape.COA23
Both are ordinarily volatile.COA24
It does not need continuous power to preserve stored bits.COA28
Choice by choice
A · incorrect — It reverses both usual properties: HDD is slower than RAM and retains data without power.
B · correct — The hierarchy places HDD below RAM in speed, and magnetic storage preserves bits without continuous power.
C · incorrect — Nonvolatility is right, but the claim that HDD is faster than RAM reverses the usual hierarchy.
D · incorrect — Slower is right, but volatile contradicts the note’s explicit HDD power-off retention statement.
Question 158
Which range matches the historical optical-disk access-time examples used in this course, rather than a universal specification for every optical drive?
A. 1–5 milliseconds
B. 10–30 milliseconds
C. 100–300 milliseconds
D. 500–1000 milliseconds
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
The note identifies one hundred to three hundred milliseconds as a historical optical-access example. That range is not a universal specification: actual timing depends on the device and measurement conditions. The revised stem asks for the particular teaching range rather than an unqualified typical value for all optical disks. The remaining intervals do not match that historical example and therefore are definite distractors.
Evidence in the complete study note
Optical access ranges such as 100–300 ms are historical examples, not universal device specifications.COA28
Choice by choice
A · incorrect — This interval does not match the historical optical-access example.
B · incorrect — This shorter interval is not the course’s cited historical example.
C · correct — This is the historical example range given in the note.
D · incorrect — This longer interval is not the course’s cited historical example.
Question 159
Which storage medium accesses data sequentially rather than randomly?
A. SSD
B. HDD
C. Magnetic tape
D. Optical disk
Hint / Module Reference (Where to Read)
Separate storage role, access timing, placement and power retention; use the specified hierarchy or mapping convention.
COA28 classifies tape as sequential and suited to streaming/archives. Disk provides direct addressed-block access, while SSD provides nonmechanical persistent storage rather than a tape-style stream. The question asks the medium whose access is characteristically sequential, so magnetic tape is the supported choice. Physical streaming inside another device does not make its logical access interface tape-like.
Evidence in the complete study note
Optical media use lasers; tape is suited to sequential streaming and archives.COA28
In textbook access taxonomy, tape is sequential, disk is direct access with positioning delay, RAM is random access with broadly address-independent timing, and associative access matches content.COA28
Choice by choice
A · incorrect — SSD is addressed nonvolatile semiconductor storage rather than the sequential tape-access medium described.
B · incorrect — HDD permits addressed-block direct access rather than requiring tape-like sequential record traversal.
C · correct — Tape is explicitly the sequential streaming/archive medium in the note’s access taxonomy.
D · incorrect — Optical disk uses addressed disk access rather than being the sequential tape medium requested.
Question 160
Registers within the CPU are used primarily to:
A. Store large datasets permanently
B. Hold temporary data for immediate CPU operations
C. Communicate with I/O devices
D. Manage virtual memory pages
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: B — Hold temporary values for immediate CPU operations.
COA14 distinguishes registers as explicit execution operands and assigns them fetched instructions, transferred data and operands/results. That supports the immediate temporary-storage role in B. Registers are small execution state rather than permanent bulk data storage. Some registers participate in I/O or translation, but those specialized uses do not replace the primary execution-storage role asked here.
Evidence in the complete study note
IR holds the fetched instruction; MAR holds an address used for the current memory access; MDR holds transferred data.COA14
The accumulator holds operands/results, SP tracks the stack, and status flags report conditions.COA14
Registers and cache both store temporary information, but registers are explicit execution operands and cache holds copies of memory blocks.COA14
Choice by choice
A · incorrect — Registers are small temporary execution storage rather than permanent bulk storage for large datasets.
B · correct — Registers hold operands, instruction state and intermediate results used directly by current CPU operations.
C · incorrect — Some registers support I/O, but general I/O communication is not their primary execution-storage purpose.
D · incorrect — Translation can use specialized state, but managing virtual pages is not the primary role of CPU registers generally.
Question 161
The address bus in a computer system is responsible for:
A. Carrying actual data between components
B. Specifying the memory location the CPU wants to access
C. Providing timing signals
D. Transmitting control commands
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: B — Specify the addressed memory location.
COA12 says address signals select a location, data signals carry values and control signals coordinate read/write and timing. Therefore B directly matches the address bus. Actual payload data belongs to the data bus, while timing and operation commands belong to control signaling. The distinction does not depend on address width or the value being transferred.
Evidence in the complete study note
Address signals select a location; data signals carry values; control signals coordinate read/write, timing, requests and acknowledgements.COA12
Choice by choice
A · incorrect — Actual payload values travel on the data bus rather than the address signals selecting a location.
B · correct — The address bus identifies the memory location selected for the CPU’s access.
C · incorrect — Timing belongs to control signaling, not the location-selection role of address signals.
D · incorrect — Read/write and other operation commands belong to control signaling rather than the address bus.
Question 162
A CPU exposes 32 address bits and uses byte-addressable memory with no additional address-extension mechanism. What maximum byte capacity can it address? Use GB here to mean 2^30 bytes.
A. 2 GB
B. 4 GB
C. 8 GB
D. 16 GB
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Thirty-two address bits identify 2^32 distinct locations. With one byte per location, that is 2^32 bytes, or four units of 2^30 bytes. The selected option is therefore four GB under the explicitly stated binary convention, more precisely four GiB. Data-bus width is irrelevant to this location count, and without byte addressing the same number of address bits would not determine a byte capacity.
Evidence in the complete study note
With a address bits there are 2^a addressable locations.COA12
Multiply by bytes per location before calling this a byte capacity.COA12
Choice by choice
A · incorrect — Two binary gigabytes would require only 2^31 byte locations.
B · correct — 2^32 byte locations equal four units of 2^30 bytes.
C · incorrect — Eight binary gigabytes would require 33 address bits.
D · incorrect — Sixteen binary gigabytes would require 34 address bits.
Question 163
The control bus in a computer system carries:
A. Data between CPU and memory
B. Memory addresses
C. Signals that regulate operations like read/write timing
D. Interrupt requests only
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: C — Control signals coordinate operations, including read/write timing.
COA12 defines control signals as coordinating read/write, timing, requests and acknowledgements. C expresses that general role. The data and address alternatives belong to distinct signal groups. Interrupt requests may be part of aggregate control, but the word only makes D too restrictive because read/write and timing controls are also included.
Evidence in the complete study note
Address signals select a location; data signals carry values; control signals coordinate read/write, timing, requests and acknowledgements.COA12
Aggregate control signals include both CPU outputs and device inputs; both data and control buses can therefore be bidirectional under that scope.COA12
Choice by choice
A · incorrect — Actual transferred data belongs to the data bus rather than the control-signal group.
B · incorrect — Location selection belongs to address signals rather than the control bus’s coordination role.
C · correct — Read/write coordination and timing are explicitly among the functions assigned to control signals.
D · incorrect — Interrupt requests are only one possible control input; the bus also carries other coordination signals.
Question 164
In instruction format terminology, an 'opcode' refers to:
A. The memory address of the next instruction
B. The bits specifying the operation to perform
C. The register holding the result
D. The data value being processed
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: B — Bits specifying the operation.
COA16 defines the opcode as the operation-specifying field. Operand fields locate registers/data and mode fields explain their interpretation. Thus B names the correct format role; next-instruction addresses, result-register identity and operand values are separate quantities. Their presence elsewhere in a machine does not change what opcode means.
Evidence in the complete study note
An opcode specifies the operation; operand fields locate data or registers, and a mode field explains interpretation.COA16
Choice by choice
A · incorrect — Next-instruction position is a PC/control-flow role, not the opcode’s operation-selection role.
B · correct — Opcode bits select the operation the processor should perform for the instruction.
C · incorrect — Result-register selection belongs to an operand/destination field rather than defining the opcode.
D · incorrect — An operand data value is distinct from the code selecting the operation to apply.
Question 165
A zero-address instruction format relies on:
A. Implicit register addressing
B. Stack-based operand access
C. Immediate values only
D. Direct memory addressing
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: B — Implicit top-of-stack operands.
COA16 says zero-address stack ADD uses two implicit top-of-stack operands. The absence of written operand addresses therefore relies on stack organization, not immediate constants or direct memory fields. Generic implicit register addressing is too broad and does not identify the stack discipline specified for this format; PUSH/POP may still have explicit addresses.
Evidence in the complete study note
Zero-address stack ADD uses two implicit top-of-stack operands.COA16
PUSH and POP may still contain an explicit address even on a stack machine.COA17
Choice by choice
A · incorrect — Implicit register addressing alone does not identify the stack operand convention defining zero-address arithmetic here.
B · correct — Operands come implicitly from the top of the stack, so arithmetic needs no explicit operand-address fields.
C · incorrect — Immediate values require encoded operand information; zero-address stack arithmetic is not restricted to constants.
D · incorrect — Direct memory addressing would use an explicit operand address, contrary to the stated zero-address arithmetic format.
Question 166
Which instruction format is most expressive, allowing operations on three separate operands?
A. Zero-address
B. One-address
C. Two-address
D. Three-address
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
COA16 defines three-address ADD X,Y,Z as X←Y+Z, allowing a separately named destination and two sources. This matches the stem’s three separate operands. Two-address form overwrites one source, one-address uses an implicit accumulator, and zero-address uses stack operands. Most expressive is interpreted here through the explicit three-operand criterion rather than a universal comparison of complete instruction sets.
Evidence in the complete study note
Three-address ADD X,Y,Z means X←Y+Z under destination-first notation.COA16
Two-address ADD X,Y overwrites X with X+Y.COA16
One-address accumulator ADD X means AC←AC+M[X].COA16
Zero-address stack ADD uses two implicit top-of-stack operands.COA16
Choice by choice
A · incorrect — Zero-address arithmetic names no explicit operands and instead uses the implicit stack top.
B · incorrect — One-address accumulator arithmetic names only one explicit operand and relies on an implicit accumulator.
C · incorrect — Two-address arithmetic overwrites a named source and lacks a separately named third operand field.
D · correct — Three explicit fields allow one destination and two independently named source operands.
Question 167
Stack organization follows which principle?
A. FIFO (First In First Out)
B. LIFO (Last In First Out)
C. Random Access
D. Priority-based Access
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
COA17 defines a stack as last-in, first-out: PUSH adds at the logical top and POP removes that top item. The most recently pushed remaining item is therefore the next removed. FIFO describes queue ordering, while arbitrary indexed access or priority selection does not define the stack discipline.
Evidence in the complete study note
A stack is last-in, first-out.COA17
PUSH adds an item and POP removes the logical top.COA17
Choice by choice
A · incorrect — FIFO removes the oldest inserted item, the opposite order from normal stack removal.
B · correct — The last item pushed becomes the top and is the first item popped.
C · incorrect — Random access does not enforce removal of the most recently pushed remaining item.
D · incorrect — Stack removal follows insertion order in reverse, not a priority ranking assigned to items.
Question 168
In indirect addressing mode, the instruction contains:
A. The actual data value
B. The direct memory address of the data
C. A pointer to the memory address where data resides
D. A register number
Hint / Module Reference (Where to Read)
Identify the register, signal or instruction role and the execution phase; distinguish stored values, addresses and control actions.
Correct answer: C — A reference whose stored contents supply the effective address.
COA18 defines memory-indirect addressing as EA=M[A], followed by operand M[EA]. Thus the instruction’s field identifies a pointer location rather than directly containing the operand value or final operand address. C is the pointer/indirection description. A describes immediate, B direct, and a plain register number identifies a register-based mode rather than this memory-indirect convention.
Evidence in the complete study note
Let A be an instruction field, R a register value and M[x] the contents at x.COA18
Immediate uses value A; direct uses EA=A and operand M[A]; indirect uses EA=M[A] then operand M[EA].COA18
Correct answer: C — Simple operations, regular encodings and load/store memory access
Textbook RISC emphasizes simple operations, regular encodings, load/store memory access and pipeline-friendly control. These tendencies do not imply every instruction completes with one-cycle latency; steady-state pipeline throughput is a separate measure. Variable lengths and complex operations are associated with CISC tendencies, while an instruction-count range is not a defining guarantee. The choice states these RISC characteristics without imposing a universal single-cycle latency.
Correct answer: C — CISC commonly supports richer complex instructions, potentially with multi-cycle execution.
COA20 associates CISC with complex operations, richer addressing and variable lengths, and rejects universal one-cycle latency claims. C therefore gives the matching tendency and permits, rather than requires, multi-cycle execution. The remaining claims either reverse the usual complexity contrast or impose unsupported only/no restrictions. The answer does not claim modern RISC instructions can never take multiple cycles.
COA20 explicitly lists plentiful registers among textbook RISC characteristics, alongside load/store access and simple operations. C is therefore the supported tendency. More addressing modes and instruction bytes are not the stated compensating mechanism, and more cycles per instruction is not a defining guarantee. The typically qualifier matters because the labels alone do not impose a register count on every implementation.
COA30 defines programmed/polled I/O as repeatedly checking device status while the CPU moves each item. B names that readiness/completion checking mechanism. Interrupt notification belongs to interrupt-driven I/O, and a DMA controller is a separate transfer mechanism. The OS may arrange when polling code runs, but that broad scheduling statement does not replace the actual status check.
Evidence in the complete study note
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
Choice by choice
A · incorrect — An interrupt signal names interrupt-driven notification rather than programmed I/O’s polling mechanism.
B · correct — The CPU reads device status repeatedly to determine readiness or completion in programmed I/O.
C · incorrect — DMA-controller completion notification belongs to a DMA transfer rather than programmed CPU-driven I/O.
D · incorrect — Scheduling a check is broader software organization; polling the status register is the actual completion-detection method.
Question 173
The main advantage of Interrupt-Driven I/O over Programmed I/O is:
A. Higher data transfer speeds
B. The CPU can perform other tasks while waiting for I/O
C. It requires no special hardware
D. It eliminates the need for device drivers
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Correct answer: B — The CPU can do other work while the device operates.
COA30 says interrupt-driven I/O lets the CPU do other work until the device requests service. That removes continuous status polling, which is the principal advantage in B. Service still consumes CPU time and needs device support/software. Therefore it does not universally increase device transfer speed, eliminate hardware requirements or remove drivers.
Evidence in the complete study note
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
A controller is hardware; a driver is software that operates it.COA29
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Choice by choice
A · incorrect — Avoiding polling does not by itself guarantee that the device or bus transfers data at a higher rate.
B · correct — The CPU can execute other useful work between setup and the device’s service request.
C · incorrect — Interrupt notification requires suitable device/controller support; the note does not promise no special hardware.
D · incorrect — A handler/driver must still service the device; interrupt-driven operation does not remove that software role.
Question 174
Direct Memory Access (DMA) primarily improves performance by:
A. Increasing CPU clock speed
B. Allowing a controller to transfer data between an I/O device and memory without the CPU copying each word
C. Compressing data before transfer
D. Using a faster bus
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Correct answer: B — Allowing a controller to transfer data between an I/O device and memory without the CPU copying each word
DMA transfers a block directly between an I/O device and memory after CPU setup. Its performance benefit is reduced per-word CPU copying, leaving the processor available for other work while the controller performs the transfer. CPU configuration and completion handling remain necessary, and DMA still consumes memory bandwidth. It does not inherently raise the clock, compress data or require a faster bus.
Evidence in the complete study note
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
DMA does not eliminate CPU involvement in configuration, ownership, address mapping or completion.COA30
DMA reduces per-word CPU work but competes for memory bandwidth.COA30
Choice by choice
A · incorrect — DMA changes who performs transfer work, not the processor’s clock frequency.
B · correct — The controller moves the block after setup, avoiding a CPU copy operation for every transferred word.
C · incorrect — Data compression is not part of the DMA definition or its stated per-word CPU-work reduction.
D · incorrect — DMA may use the existing bus and does not inherently replace it with a faster one.
Question 175
In Memory-Mapped I/O, how are I/O devices accessed?
A. Using special IN/OUT instructions
B. Through dedicated I/O ports separate from memory
C. By assigning memory addresses to I/O registers, accessed like regular memory
D. Via DMA exclusively
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Correct answer: C — Device registers occupy memory addresses and use suitable memory access instructions.
COA31 says memory-mapped I/O assigns device registers addresses in the memory address space and uses suitable loads/stores. C matches, but like regular memory refers to address/instruction access rather than identical side effects: MMIO widths, ordering and status-read behavior still matter. Special IN/OUT and a separate port space instead describe isolated I/O; DMA is independent of address-space choice.
Evidence in the complete study note
Memory-mapped I/O assigns device registers addresses in the memory address space and uses suitable load/store operations.COA31
Isolated/port-mapped I/O has a separate port space and special instructions such as IN/OUT.COA31
MMIO must respect device access widths, ordering and side effects; a status read is not necessarily a harmless RAM read.COA31
Choice by choice
A · incorrect — Special IN/OUT instructions describe isolated/port-mapped I/O rather than the defining memory-mapped access mechanism.
B · incorrect — A separate port space is the isolated I/O arrangement, not device registers in memory address space.
C · correct — MMIO places device registers at memory-space addresses accessed through suitable loads/stores, with device-specific side-effect rules.
D · incorrect — MMIO specifies addressing and access, not an exclusive requirement to transfer all device data through DMA.
Question 176
An I/O 'Write Command' instructs the I/O module to:
A. Read data from the peripheral and store it in a buffer
B. Check the device status for errors
C. Take data from the data bus and transmit it to the peripheral
D. Reset the peripheral device
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Correct answer: C — Transmit system data to the peripheral.
COA29 defines write/output commands as sending system data to the device. C matches that direction: data from the system bus is handed to the peripheral. Reading brings device data toward the system, status testing inspects readiness/errors, and reset is a control action. These are distinct command functions even when one controller implements them all.
Evidence in the complete study note
Control commands start actions, test/status commands inspect readiness or errors, read commands bring device data toward the system, and write/output commands send system data to the device.COA29
Choice by choice
A · incorrect — Moving peripheral data into a system buffer is the input/read direction rather than write/output.
B · incorrect — Checking readiness or errors is a test/status command rather than transferring output data.
C · correct — A write/output command sends data from the system side to the peripheral device.
D · incorrect — Reset is a device-control action, not the ordinary data-output direction defining a write command.
Question 177
Which I/O technique is most efficient for transferring large blocks of data, such as disk reads?
A. Programmed I/O
B. Interrupt-Driven I/O
C. Direct Memory Access (DMA)
D. Memory-Mapped I/O
Hint / Module Reference (Where to Read)
Follow the data path and control responsibility; distinguish the transfer mechanism, address space and interface type.
Correct answer: C — DMA for substantial block transfers.
COA30 explicitly recommends DMA for substantial blocks because it reduces per-word CPU work to setup and completion duties. This matches disk-like large transfers. Polling and interrupt transfer still involve CPU servicing of individual items, while memory-mapped I/O is an address-space design choice that may coexist with DMA. The answer assumes the substantial-block context, not a universal fastest mechanism for every tiny transfer.
Evidence in the complete study note
Programmed/polled I/O repeatedly checks status and lets the CPU move each item.COA30
Interrupt-driven I/O lets the CPU do other work until an event requests service; the handler still consumes CPU time to service the device.COA30
DMA lets a controller move a block directly between device and memory after CPU setup.COA30
Choose it for substantial blocks; mapping devices to addresses is a separate design dimension.COA30
Choice by choice
A · incorrect — Programmed I/O makes the CPU check status and move each item, adding substantial work for large blocks.
B · incorrect — Interrupt-driven transfer avoids continuous polling but still consumes CPU service work for transferred items.
C · correct — DMA replaces much per-item CPU work with block setup/completion, matching the substantial-transfer recommendation.
D · incorrect — Memory mapping specifies device addressing and can coexist with DMA; it does not itself offload block movement.
Question 178
SMP (Symmetric Multiprocessing) systems are characterized by:
A. Multiple different processors with specialized roles
B. Compatible peer processors sharing memory and I/O under one operating system
C. Processors with separate private address spaces communicating by messages
D. Independent networked computers without shared memory
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Correct answer: B — Compatible peer processors sharing memory and I/O under one operating system
SMP gives processors peer roles with shared memory and I/O under an operating system. Compatibility and symmetric roles matter; every physical processor property need not be identical. Specialized asymmetric roles do not state that model, while separate address spaces and independent networked computers describe distributed organization. The alternatives compare coherent organizations without an impossible single-processor multi-chip description.
Evidence in the complete study note
SMP processors share memory/I/O and have peer roles under an OS.COA37
Distributed-memory systems communicate between separate address spaces.COA37
Choice by choice
A · incorrect — Specialized unequal processor roles describe an asymmetric organization rather than the peer-role model.
B · correct — Peer roles with shared memory and I/O under one OS match the SMP definition.
C · incorrect — Separate private address spaces and message communication describe distributed-memory organization.
D · incorrect — Independent computers without shared memory do not have the stated SMP shared-memory organization.
Question 179
Pipelining improves CPU performance by:
A. Increasing the clock speed of each stage
B. Executing one instruction at a time faster
C. Overlapping the execution stages of multiple instructions simultaneously
D. Using larger registers
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Correct answer: C — Overlap stages of different instructions.
COA35 defines pipelining by overlapping stages from different instructions and says it primarily improves throughput. C directly states that mechanism. It does not require faster stages, larger registers or a single instruction completing all work faster. Pipeline fill/drain, stalls and the slowest stage constrain actual gains, so overlap rather than guaranteed latency reduction is the supported explanation.
Evidence in the complete study note
A pipeline overlaps stages of different instructions; it primarily improves throughput.COA35
The ideal steady-state completion rate is one instruction per cycle, while an individual instruction still spans multiple stages.COA35
Choice by choice
A · incorrect — Pipeline performance does not require increasing each stage’s clock speed; clock choice is limited by the slowest stage.
B · incorrect — An instruction still spans several stages, so lower single-instruction latency is not the defining improvement.
C · correct — Overlapping stages lets different instructions progress concurrently, increasing completed-work throughput.
D · incorrect — Larger register width does not define stage overlap or directly explain pipelining’s throughput benefit.
Question 180
In an arithmetic pipeline for floating-point addition, which is the FIRST sub-operation performed?
A. Normalize the result
B. Add/subtract the mantissas
C. Align the mantissas
D. Compare the exponents
Hint / Module Reference (Where to Read)
Keep the radix, bit width and representation fixed; evaluate place values or arithmetic steps in order.
COA10 orders floating addition as compare exponents, shift the smaller significand to align, add/subtract, normalize and round. Comparing exponents must precede alignment because their difference determines the required shift. Adding before alignment combines unequal place weights, and normalization happens after arithmetic. Therefore D is the first named sub-operation.
Evidence in the complete study note
For floating addition, compare exponents, shift the smaller significand to align, add or subtract, normalize and round.COA10
Choice by choice
A · incorrect — Normalization follows aligned addition/subtraction rather than initiating the floating-point addition sequence.
B · incorrect — Significands must first be aligned to a common exponent before their values can be added correctly.
C · incorrect — Alignment follows exponent comparison, which determines which significand to shift and by how much.
D · correct — Exponent comparison is explicitly first and supplies the information needed for subsequent alignment.
Question 181
Which statement describes vector-instruction semantics rather than guaranteeing simultaneous execution of every array element?
A. Processes one element at a time faster
B. One vector instruction applies an operation across multiple data elements, possibly in lane-sized batches
C. Uses fewer transistors
D. Operates at a higher clock frequency
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Correct answer: B — One vector instruction applies an operation across multiple data elements, possibly in lane-sized batches
A vector instruction describes an operation over a sequence of elements. Its semantics cover multiple data elements, but physical lanes can process those elements in batches instead of executing the entire array at one instant. The choice distinguishes vector from scalar processing without requiring simultaneous execution of every element. Faster individual elements, fewer transistors or a higher clock are implementation properties rather than definitions of vector processing.
Evidence in the complete study note
A vector instruction describes an operation over a sequence of elements; physical lanes may process them in batches, not all in one instant.COA37
Choice by choice
A · incorrect — Faster scalar element processing does not define vector semantics.
B · correct — This states the multi-element instruction semantics while permitting physical batching.
C · incorrect — A transistor-count reduction is not part of the definition.
D · incorrect — A higher clock frequency is not required by vector semantics.
Question 182
For an ideal single-issue RISC pipeline in steady state after filling, with balanced stages and no stalls, what is the completion throughput?
A. One instruction per two clock cycles
B. One instruction per clock cycle
C. Two instructions per clock cycle
D. Depends on instruction complexity
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Correct answer: B — One instruction per clock cycle
An ideal single-issue pipeline overlaps stages of successive instructions. After filling, it completes one instruction each cycle when stages are balanced and no hazards or other stalls interfere. An individual instruction still crosses several stages, so this is throughput rather than one-cycle instruction latency. Specifying single issue excludes a superscalar interpretation that could complete more than one instruction per cycle.
Evidence in the complete study note
In an ideal k-stage single-issue pipeline, n instructions take k+n−1 cycles when stages are balanced and there are no stalls.COA35
The ideal steady-state completion rate is one instruction per cycle, while an individual instruction still spans multiple stages.COA35
Choice by choice
A · incorrect — One completion per two cycles is below the stated ideal no-stall rate.
B · correct — The ideal steady-state single-issue completion rate is one per cycle.
C · incorrect — Two per cycle requires multiple-issue resources beyond the stated design.
D · incorrect — The ideal rate follows from the specified single-issue pipeline assumptions.
Question 183
Flynn's taxonomy classifies parallel computer architectures based on:
A. Number of processors and memory size
B. Instruction streams and data streams
C. Clock speed and bus width
D. Cache size and register count
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Correct answer: B — Instruction streams and data streams.
COA37 explicitly defines Flynn classification by instruction and data streams. SISD has one of each, SIMD one instruction stream with multiple data elements, and MIMD multiple streams of each. Processor count, capacity, clock and register/cache sizes are implementation properties rather than the two classification axes. Therefore B directly matches the taxonomy.
Evidence in the complete study note
Flynn classifies instruction and data streams: SISD has one of each; SIMD applies one instruction stream to multiple data elements; MIMD uses multiple instruction and data streams; MISD has multiple instruction streams for a common data stream and is uncommon.COA37
Choice by choice
A · incorrect — Processor count and memory size do not define the instruction-stream/data-stream axes of Flynn’s taxonomy.
B · correct — Flynn classifies the number of instruction streams and data streams, producing SISD/SIMD/MISD/MIMD categories.
C · incorrect — Clock and bus width measure implementation characteristics rather than Flynn’s stream-count classification.
D · incorrect — Cache capacity and register count are not the two axes used by Flynn’s taxonomy.
Question 184
The primary goal of parallel processing is to increase:
A. Memory capacity
B. Clock frequency
C. Throughput — the amount of processing per unit time
D. Register size
Hint / Module Reference (Where to Read)
Separate throughput from latency and check which operations overlap or share resources under the stated model.
Correct answer: C — Throughput: completed processing per unit time.
COA37 says more cores increase available parallel work while serial dependencies and coordination limit speedup. COA34 defines throughput as completed work per unit time. Parallel processing aims to raise that work rate, matching C, rather than inherently increasing physical memory, clock frequency or register width. Actual gains still depend on enough independent work and manageable overhead.
Evidence in the complete study note
More cores increase available parallel work, but serial dependencies and coordination limit speedup.COA37
Throughput counts completed work per unit time; latency measures one job’s delay.COA34
Choice by choice
A · incorrect — Parallel execution does not inherently increase the system’s installed memory capacity.
B · incorrect — Additional concurrent work can improve throughput without increasing any processor’s clock frequency.
C · correct — Concurrent useful work aims to increase completed processing per unit time, subject to serial and coordination limits.
D · incorrect — Register width is an architectural data-size property, not the primary objective of parallel execution.